請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70232
標題: | 利用虛擬側向力與塑性分析法探討挫屈束制支撐整體面外穩定性 A Study of Global Out-of Plane Stability Model for BRBs Using Notional Load and Plastic Analysis |
作者: | I-CHIA OU 歐易佳 |
指導教授: | 蔡克銓(Keh-Chyuan Tsai) |
關鍵字: | 挫屈束制支撐,圍束單元撓曲效應,端部面外位移,面外穩定性,虛擬側向力,塑性分析法,二次效應,反覆載重試驗,穩定性分析模型, buckling restrained brace,flexural effect of restrainer,out-of-plane end drift,out-of-plane stability,notional load,plastic analysis,second-order effect,cyclic loading test,stability analytical model, |
出版年 : | 2018 |
學位: | 碩士 |
摘要: | 挫屈束制支撐(buckling-restrained brace, BRB)為安裝在建築內的鋼斜撐構件,受拉時可降伏消能,受壓時藉鋼管填充混凝土來提供斜撐圍束,使其亦可達降伏不發生挫屈,可有效提升建築結構的強度、勁度、韌性及消散地震能量的能力。然而,當BRB或端部接合發生挫屈破壞造成面外不穩定時,其軸向勁度與強度將大幅縮減,喪失消散能量之功能。因此近年來國際學者投入BRB面外穩定性研究,其中日本Takeuchi教授根據BRB挫屈時的塑性行為,推導出一系列挫屈預測模型。然而其所提栓接式BRB挫屈行為並不適用於國內常用之槽接式挫屈束制支撐 (WES-BRB),因此2017年陳力維延伸Takeuchi所提出之理論,考量WES-BRB其圍束單元較長之幾何特性,提出考量圍束單元撓曲效應及接合板旋轉效應之穩定性評估模型。但此理論模型仍需複雜計算程序,且須利用有限元素板殼模型分析接合板旋轉勁度及塑性彎矩容量,於實際工程應用較不方便。因此本文欲發展簡化理論模型,考慮軸力與撓曲互制之二次效應,採虛擬側向力及塑性分析法探討BRB及接合之面外穩定性。本研究以陳力維測試之四組實尺寸BRB試體進行實例分析,預測分析模型可反應接合板加勁及端部面外位移( OOP end-drift )對BRB穩定性之影響,其誤差皆小於5%。本研究另製造兩組長約7.3米,降伏強度為100噸之實尺寸BRB試體,於國家地震工程研究中心的多軸向試驗機進行反覆載重試驗,透過逐步增加端部面外位移量的方式,來探討端部面外位移量對BRB穩定性的影響並探求其臨界挫屈強度。本研究所提分析模型之預測結果可確實反應端部面外位移效應,對於挫屈強度的預測誤差小於2%,再次驗證所提模型之準確性及可靠性。因此本文使用本簡化穩定性評估模型,對業界常用的BRB噸數、構架尺寸與配置型式,利用雲端運算輔助設計軟體所規劃出的581組BRB設計案例進行挫屈強度預測與分析,分析顯示現行採容量設計法及極限狀態檢核所設計之BRB與接合例屬保守且安全。另透過多案例分析顯示,當BRB端部面外側位移角由1%增至2%時,挫屈強度減損幅度約介於12%至15%,對穩定性影響非常顯著;分析顯示若接合板邊緣有或無加勁,其挫屈強度減損幅度約介於5%至20%之間,因此於工程應用上,接合板加勁為必要之設計;而多設計案分析亦顯示外鋼管需求容量比DCR若控制在0.9之內,將使其面外穩定性更有保障。 Buckling-restrained brace (BRBs) are widely adopted for new construction and seismic retrofit of buildings. Properly fabricated BRBs can develop fully yielding strength under both tension and compression without flexural buckling. Therefore, BRBs can enhance the strength, stiffness, ductility and the energy dissipation capability of structures. However, when the out-of-plane (OOP) instability of the BRB and the end gusset connections occur, the axial strength, stiffness, and the energy dissipation capacity of the BRB will be significantly reduced. Therefore, a number of researchers have investigated the OOP stability of BRBs in recent years. Takeuchi et al. proposed a set of advanced procedures to assess the BRB OOP stability. However, their buckling models are not entirely suitable for the welded end-slot buckling restrained brace (WES-BRB), commonly used in Taiwan. Therefore, based on the unique characteristic of the WES-BRBs, Chen et al. incorporated Takeuchi’s procedures and proposed a buckling model considering flexural restrainer and gusset rotations in 2017. However, these procedures are not straight forward, requiring the finite element model analysis in order to compute the gussets’ rotational stiffness and strength. Thus, this study develops a simplified analytical model using notional load and plastic analysis to assess the OOP stability of BRBs. In order to verify the effectiveness of the proposed procedures, four full-scale BRB specimens tested by Chen et al. are used as example applications. The proposed model satisfactorily predicts specimens’ buckling strength with errors less than 5%. The effects of the OOP end drift and gusset edge stiffeners on the BRB stability are reasonably captured. In order to further verify the effectiveness of the proposed procedures, two full-scale BRB specimens each of 7.3m long with a 988-kN nominal yield strength were constructed and tested in NCREE. The experiments were conducted by applying cyclically increasing BRB axial strains while gradually increasing the OOP end drift until buckling was observed. The proposed model effectively predicts specimens’ buckling strength with errors less than 2%. Finally, parametric analysis were conducted on 581 BRB and connection cases, designed by the Brace-on-Demand (BOD) cloud service, varying from different yield strength values, frame span-to-height ratios and core plate dimensions, using the proposed procedures. Analytical results show the typical BRB and end connections designed by using the BOD service are generally conservative and safe. Results also indicate the overall stability is vulnerable to OOP end drift. The buckling strength can be reduced by 12% to 15% when the OOP end drift is increased from 1% to 2%. In addition, the buckling strength will be reduced from 5% to 20% without the presence of the gusset edge stiffeners. Thus, it can be concluded that adding the edge stiffener to the gusset is a good practice in the BRB applications. Analysis results show that when the DCR of steel casing is less than 0.9, the overall stability of BRBs can be effectively conserved. |
URI: | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70232 |
DOI: | 10.6342/NTU201803495 |
全文授權: | 有償授權 |
顯示於系所單位: | 土木工程學系 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-107-1.pdf 目前未授權公開取用 | 141.94 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。