請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70747
完整後設資料紀錄
DC 欄位 | 值 | 語言 |
---|---|---|
dc.contributor.advisor | 潘永寧(Yung-Ning Pan) | |
dc.contributor.author | Bai-Lun Zheng | en |
dc.contributor.author | 鄭百倫 | zh_TW |
dc.date.accessioned | 2021-06-17T04:37:01Z | - |
dc.date.available | 2018-08-16 | |
dc.date.copyright | 2018-08-16 | |
dc.date.issued | 2017 | |
dc.date.submitted | 2018-08-08 | |
dc.identifier.citation | [1] Min Zuo, Kun Jiang, Xiangfa Liu, “Refinement of hypereutectic Al–Si alloy by a new Al–Zr–P master alloy”, Journal of Alloys and Compounds 503,2010, L26–L30.
[2] Alireza Hekmat-Ardakan, Xichun Liu, Frank Ajersch, X.-Grant Chen, “Wear behavior of hypereutectic Al–Si–Cu–Mg casting alloys with variable Mgcontents”, Wear 269,2010, pp. 684–692. [3] 黃振賢,《機械材料》,2009,pp. 337-354。 [4] J. Gilbert Kaufman, Elwin L. Rooy, Aluminum Alloy Casting, 2004. [5] JIS Handbook, Non-Ferrous Material and Metallurgy, Japanese Standards Association, 1987-88. [6] F. Saeid and M. Saeid, “Effect of Material Structure Machining Characteristics of Hypereutectic Al-Si Alloy,” Mechanical-Advanced Manufacturing Technology, 2007, pp. 4-15. [7] D. L. Zalensas, Aluminum Casting Technology, 2nd Edition, AFS, 1993. [8] H. Ye, “An Overview of the Development of Al-Si-Alloy Based Material for Engine Applications,” Journal of Materials Engineering and Performance, Vol. 12, 2003, pp. 288-297. [9] X. Jian, H. Xu, T. T. Meek, Q. Han, “Effect of Power Ultrasound on Solidification of Aluminum A356 Alloy,” Materials Letters, Vol. 59, 2005 pp. 190-193. [10] E. N. Pan, S. W. Lin, P. C. Yu, “Improvement in Gravity-Segregation of Primary Silicon in Hyper-Eutectic Al-Si Alloys,” AFS Trans., Vol. 115, 2007, pp. 167-176 [11] F. C. Robles Hernández and J. H. Sokolowski, “Novel Image Analysis to Determine the Si Modification for Hypoeutectic and Hypereutectic Al-Si Alloys,” Journal of Metals, Vol. 57, 2005, pp. 48-52. [12] 陳武宏,《鑄鋁技術》,全華科技圖書,民國79年。 [13] John E. Gruzleski, Bernard m. Closset, “The Treatment of Liquid Aluminum-Silicon Alloys,” The American Foundrymen’s Society, 1990. [14] C. R. Ho and B. Cantor, “Heterogeneous Nucleation of Solidification of Si in Al-Si and Al-Si-P Alloys,” Acta Metall. Mater., Vol.43, 1995, pp. 3231-3246 [15] B. Cantor, “Impurity Effects on Heterogeneous Nucleation,” Materials Science and Engineering, A226-228, 1997, pp. 151-156 [16] M. Zuo, X. F. Liua, Q. Q. Sun, K. Jiang, “Effect of Rapid Solidification on the Microstructure and Refining Performance of an Al–Si–P Master Alloy”, Journal of Materials Processing Technology 209,2009, pp. 5504–5508. [17] D. A. Porter, K. E. Easterling and M. Y. Sherif, Phase Transformations in Metals and Alloys, 3rd Edition, CRC Press, 2009, pp. 196-199. [18] Haruyasu Kattoh, Akio Hashimoto, Sanji Kitaoka, Mamoru Sayashi and Masahiko Shioda, “Critical Temperature for Grain Refining of Primary Si in Hyper-Eutectic Al-Si Alloy with Phosphorus Addition,” Journal of Japan Institute of Light Metals, Vol. 52, No. 2,2002 , pp. 18-23. [19] J. Campbell, M. Tiryakioğlu, “Review of the Effect of P and Sr on Modification and Porosity Development in Al-Si Alloys,” Material Science Technology, Vol. 26, 2010, pp. 262-268. [20] G. K. Sigworth, “Theoretical and Practical Aspects of the Modification of Al-Si Alloy,” AFS Trans., Vol. 91, 1983, pp. 7-16. [21] G. Liu, G. Li, A. Cai, Z. Chen, “The Influence of Strontium Addition on Wear Properties of Al–20 wt% Si Alloys under Dry Reciprocating Sliding Condition,” Materials & Design, Vol. 32, 2011, pp. 121-126. [22] F. Yilmaz, O. A. Atasoy, “Growth Structures in Aluminium-Silicon Alloys II. The Influence of Strontium,” Journal of Crystal Growth, Vol. 118, 1992, pp. 377-384. [23] N. Tenekedjiev, D. Argo and J. E. Gruzleski, “Sodium, Strontium, and Phosphorus Effects in Hypereutectic Al--Si Alloys,” AFS Trans., Vol.97, 1989, pp. 127-136. [24] 邱弘興,〈A390鋁合金之矽形態控制及其與機械性質之關係〉,國科會85年研究計畫報告。 [25] G. K. Sigworth, “Refinement of Hypereutectic Al-Si Alloys,” AFS Trans., Vol. 95, 1987, pp. 127-136. [26] M. M. Makhlouf, H. V. Guthy, “The Aluminum–Silicon Eutectic Reaction: Mechanisms and Crystallography,” Journal of Light Metals 1, 2011, pp. 199-218. [27] S. Lu, A. Hellawell, Met. Trans. 18A, 1987, pp. 1721–1733. [28] B. Chamberlin and V. J. Zabek, “Reppraisal of the Tensile Properties of Al-Si-Mg Casting Alloys,” AFS Trans., Vol.81, 1973, pp. 322-327. [29] Kazuhiro Nogita, Stuart D. McDonald and Arne K. Dahle, “Eutectic Modification of Al-Si Alloys with Rare Earth Metals,” Materials Transactions, Vol. 45, No. 2, 2004, pp. 323-326. [30] H. Fredriksson, M. Hillert and N. Lange, “The Modification of Aluminum-Silicon Alloys by Sodium,” J. Inst. Metals, Vol. 101, 1973, pp. 285-299. [31] F. Fommei, “Modification Treatments of Al-Si Alloys,” Alumino, Vol.46, 1977, pp. 121-135. [32] J. R. Denton and J. A. Spittle, “Solidification and Susceptibility to Hydrogen Adsorption of Al-Si Alloys Containing Strontium,” Materials Science and Technology, Vol. 1, 1985, pp. 305-311. [33] H. Shahani, “Effect of Hydrogen on the Shrinkage Porosity of Aluminum Copper and Aluminum Silicon Alloys,” Scandinavian Journal of Metallurgy, Vol. 14, 1985, pp.306-312. [34] B. Closset and J. E. Gruzleski, “Mechanical Properties of A356.0 Alloys Modified with Pure Strontium,” AFS Trans., Vol. 90, 1982, pp. 453-464. [35] 陳建興,〈A356鑄造鋁輪圈之製程評估及品質改善〉,國立台灣大學機械工程研究所碩士論文,民國86年。 [36] 顏進豐,〈凝固熱參數與A356鋁合金品質之相關性研究〉,國立台灣大學機械工程研究所論文,民國87年。 [37] J. Campbell, “Feeding Mechanisms in Castings,” AFS Cast Metal Res. Journal, Vol. 5, 1969, No. 1, pp. 1-8. [38] 林文和、邱傳聖,《鑄造學》,高立圖書,pp. 260-264,民國81年。 [39] 龔肇鑄,《鑄造學》,文京圖書,民國74年。 [40] F. P. Bowden and D.Tabor, The Friction and Lubrication of Solids Part II, Oxford University Press, 2001. [41] 莊東漢,《材料破損分析》,五南圖書,2007,pp. 281-338。 [42] 陳擷安,〈A390過共晶鋁矽合金之初晶矽偏析行為及耐磨耗性研究〉,國立台灣大學機械工程研究所碩士論文,民國104年。 [43] M. Elmadagli, T. Perry and A. T. Alpas, “A Parametric Study of the Relationship Between Microstructure and Wear Resistance of Al-Si Alloys,” Wear, 262, 2007, pp. 79-92. [44] 王盈琁,〈添加合金元素對Al-17%Si合金高溫機械性質之影響〉,大同大學碩士論文,2010。 [45] 賴易辰,〈離心加壓力及熔液處理對於A390過共晶鋁矽合金之顯微組織及耐磨耗性之影響〉,國立台灣大學機械工程研究所碩士論文,民國105年。 | |
dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70747 | - |
dc.description.abstract | A390過共晶鋁矽合金(Al-17Si-4.5Cu-0.5Mg)在重力鑄造時,由於矽的比重(2.33g/cm3)較鋁(2.74g/cm3)低,因此在凝固過程中容易產生初晶矽上浮的現象,而使得同一鑄件在不同位置的機械性質有所不同。本研究係利用矽與鋁比重之差異,在凝固過程中對鑄件施加離心力,促使初晶矽的偏析現象更加顯著,預期鑄件在局部位置能達到提升耐磨耗性之目的。本研究以一自行設計之旋轉裝置進行離心鑄造,使得A390之凝固過程在旋轉狀態下受到一穩定離心力作用,促使比重較低、硬度較高的初晶矽產生顯著的徑向偏析,往旋轉軸中心側(以下稱內側)集中。藉由分析各種不同澆鑄溫度(780℃、820℃)和轉速(400 rpm、450 rpm、…、650 rpm)下鑄件在不同位置(內側、中央、外側)之顯微組織。實驗結果顯示,當鑄造溫度較高時,偏析現象較為明顯,且初晶矽之偏析程度會隨旋轉速度之增加而提高,當轉速達到550rpm時,偏析程度達到飽和,而不再隨旋轉速度增加而提高。故,本研究之離心鑄造實驗,其溫度及轉速分別設定為820℃及500 rpm。
又,本研究在固定轉速500rpm之離心鑄造條件下,探討P之細化處理(針對初晶矽)與Sr調質處理(針對共晶矽)對於A390過共晶鋁矽合金之顯微組織及耐磨耗性之影響,最後利用迴歸分析以獲致各參數與耐磨耗性之間的關係。實驗結果顯示,經離心鑄造之A390鑄件其耐磨耗性皆以內側(接近旋轉軸)為最佳,符合本研究之預期結果(以離心鑄造提升A390初晶矽集中處之耐磨耗性)。在細化初晶矽方面,進行細化處理後可使初晶矽顆粒平均尺寸由98μm降低至61μm;在調質共晶矽方面,進行調質處理後可使共晶矽平均調質級數達到AFS 4~5級,但會使初晶矽顆粒平均尺寸增加至208μm。所有爐次中以添加0.02%P之細化劑、持溫10分鐘之細化處理所獲之離心鑄件內側之耐磨耗性為最佳,以數據比較來表示(選擇一比較基準,計算磨耗率之降低百分比)。最後,進行磨耗率與相關參數之綜合迴歸分析,分析結果得知:當初晶矽面積率愈大、初晶矽顆粒尺寸愈小、共晶矽調質級數愈大、硬度愈高,則磨耗率愈小,亦即耐磨耗性愈佳。 | zh_TW |
dc.description.abstract | While casting the A390 hypereutectic aluminum alloy, primary Si particles tend to float to the upper part of the casting due to the difference in specific weight between the primary Si particles and the aluminum bulk liquid, the so-called gravity segregation. As a result, the mechanical properties in different parts of the casting vary. Utilizing the above-mentioned phenomenon of the primary silicon gravity segregation, the present study further enhanced this segregation nature by employing centrifuging casting process to achieve better wear resistance in specific areas of the castings. A centrifuging casting apparatus was constructed which allows the casting to be solidified under the centrifugal force. Under the centrifuging casting condition, the primary silicon particles which have low specific gravity and high hardness tend to move toward the rotational axis and aggregate at the inner portion of the castings. By analyzing the microstructures of different parts of the casting under different pouring temperatures (780, 820℃) and rotational speeds (400 rpm, 450 rpm, …, 650 rpm), we concluded that the degree of primary silicon segregation toward the inner portion of the casting increases with increasing both pouring temperature and rotational speed, and reaches a plateau at 500 rpm. Therefore, a pouring temperature of 820℃and a rotational speed of 500rpm were chosen in this study.
In addition, P refinement (for primary Si) and Sr modification (for eutectic Si) were performed to examine the effects of either P refinement or Sr modification on the microstructures of the centrifuging castings at 500 rpm. The microstructure of the A390 alloy without any treatments exhibits somewhat large primary Si particles with an average size of some 98μm, and acicular type eutectic Si of class 1. When the alloy was refined with 0.02%P, the size of the primary Si was substantially reduced to about 61μm, while the eutectic Si remained more or less unchanged. On the other hand, when the alloy was modified by 0.02%Sr, the eutectic Si was improved to class 4-5, while the primary Si was coarsened significantly to about 208μm. Furthermore, the effects of the microstructure features on the wear resistance property of A390 alloy was studied, and regression analyses were performed by correlating the four main dependent variables, namely, the area ratio of the primary Si (X, %), the average primary Si size (Y,μm), degree of eutectic Si modification (Z, class), and hardness (H, HRC) with the wear rate (W, mm3/m). The obtained regression equation is: W = 0.249367 – 0.00225X + 0.000393Y – 0.02212Z – 0.00382H. The regressing equation indicates that the wear rate can be reduced by increasing area ratio of the primary Si, decreasing primary Si size, increasing degree (class) of eutectic Si modification, and enhancing harness. | en |
dc.description.provenance | Made available in DSpace on 2021-06-17T04:37:01Z (GMT). No. of bitstreams: 1 ntu-106-R04522704-1.pdf: 7416503 bytes, checksum: ff4420e1d7b8cdfa8e04d444309a902f (MD5) Previous issue date: 2017 | en |
dc.description.tableofcontents | 口試委員會審定書 #
誌謝 i 中文摘要 ii ABSTRACT iii CONTENTS v LIST OF FIGURES viii LIST OF TABLES x Chapter 1 前言 1 Chapter 2 文獻探討 2 2.1 鋁合金簡介 2 2.1.1 鋁的特性 2 2.1.2 鋁合金的分類 2 2.1.3 合金元素對鋁合金的影響 2 2.2 鑄造用Al-Si合金系 5 2.3 A390過共晶鋁矽合金 5 2.3.1 初晶矽及其細化處理(Refinement) 6 2.3.2 共晶矽及其調質處理(Modification) 7 2.4 鋁合金鑄件中的孔洞 8 2.4.1 氫氣孔(Hydrogen Porosity) 9 2.4.2 縮孔(Shrinkage Porosity) 9 2.5 離心加壓鑄造法 10 2.6 固體在熔液中之移動速度 11 2.7 浮力原理-阿基米德定律 12 2.8 磨耗行為 12 2.8.1 磨耗概論 12 2.8.2 磨耗機制 13 2.8.3 影響磨耗行為之參數 14 Chapter 3 實驗方法與步驟 30 3.1 實驗目的 30 3.2 實驗設計 30 3.2.1 旋轉裝置 31 3.2.2 鑄件模型與CO2砂模 31 3.2.3 熔煉與澆鑄 32 3.3 試片取樣 33 3.4 顯微組織觀察 33 3.4.1 初晶矽之面積率量測 33 3.4.2 孔洞之面積率量測 33 3.4.3 共晶矽調質效果量化 34 3.4.4 初晶矽尺寸量測 34 3.5 耐磨耗試驗 34 Chapter 4 結果與討論 47 4.1 第一部分:決定最佳離心轉速及熔解溫度 47 4.1.1 爐次A-L-400、A-L-450、A-L-500(無處理、離心鑄造、L:780℃、轉速:400、450、500rpm) 47 4.1.2 爐次A-H-400、A-H-450、A-H-500、A-H-550、A-H-600、A-H-650 (無處理、離心鑄造、H:820℃、轉速:400~650rpm) 47 4.1.3 小結 48 4.2 第二部分:細化及調質處理對於離心加壓鑄造顯微組織之影響 48 4.2.1 爐次G(無處理、重力鑄造) 48 4.2.2 爐次A(無處理、離心鑄造) 49 4.2.3 爐次B(0.02%P初晶矽細化處理、離心鑄造) 49 4.2.4 爐次C(0.02%Sr共晶矽調質處理、離心鑄造) 49 4.2.5 小結 50 4.3 耐磨耗性能 50 4.3.1 耐磨耗試驗結果 51 4.3.2 各種不同參數對於A390耐磨耗性之影響 51 Chapter 5 結論 68 REFERENCE 70 | |
dc.language.iso | zh-TW | |
dc.title | A390過共晶鋁矽合金之離心加壓鑄造製程研發 | zh_TW |
dc.title | The Centrifuging Casting Process of A390 Hyper-eutectic
Al-Si Alloy | en |
dc.type | Thesis | |
dc.date.schoolyear | 106-2 | |
dc.description.degree | 碩士 | |
dc.contributor.oralexamcommittee | 楊智富(Chih-Fu Yang),許正勳(Cheng-Hsun Hsu) | |
dc.subject.keyword | A390鋁合金,離心加壓鑄造,初晶矽偏析,細化處理,調質處理,耐磨耗性, | zh_TW |
dc.subject.keyword | A390 aluminum alloy,Centrifuging casting,Primary Si segregation,Refinement,Modification,Wear resistance property, | en |
dc.relation.page | 72 | |
dc.identifier.doi | 10.6342/NTU201701482 | |
dc.rights.note | 有償授權 | |
dc.date.accepted | 2018-08-08 | |
dc.contributor.author-college | 工學院 | zh_TW |
dc.contributor.author-dept | 機械工程學研究所 | zh_TW |
顯示於系所單位: | 機械工程學系 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-106-1.pdf 目前未授權公開取用 | 7.24 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。