請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/63900
完整後設資料紀錄
DC 欄位 | 值 | 語言 |
---|---|---|
dc.contributor.advisor | 盧信嘉(Hsin-Chia Lu) | |
dc.contributor.author | Shiu-Shiang Tung | en |
dc.contributor.author | 童旭祥 | zh_TW |
dc.date.accessioned | 2021-06-16T17:22:28Z | - |
dc.date.available | 2015-08-28 | |
dc.date.copyright | 2013-08-28 | |
dc.date.issued | 2012 | |
dc.date.submitted | 2012-08-16 | |
dc.identifier.citation | [1] Kai Zoschke, M. Jurgen Wolf, Michael Topper, Oswin Ehrmann, Thomas Fritzsch, Karin Kaletta, Franz-Josef Schmuckle, and Herbert Reichl. “Fabrication of application specific integrated passive devices using waferlevel packaging technologies,” IEEE Trans. on Adv. Packag., vol. 30, no. 3, pp. 359-368, Aug. 2007.
[2] Gwang-Hoon Lee, Chan-Sei Yoo, Jong-Gwan Yook, and Jun-Chul Kim, “SIW(substrate intergrated waveguide) quasi-elliptic filter based on LTCC for 60-GHz application,” European Microwave Integrated Circuits Conference, pp. 204-207, Sep. 2009. [3] Hung-Yi Chien, Tze-Min Shen, Ting-Yi Huang, Wei-Hsin Wang and Ruey-Beei Wu, “Miniaturized bandpass filters with double-folded substrate integrated waveguide resonators in LTCC,” IEEE Trans. Microwave Theory and Tech., vol. 57, no. 7, pp. 1774-1782, July 2009. [4] Ming-Fong Lei and Huei Wang, “Implementation of reduced-size dual-mode ring filters in LTCC and MMIC processes at millimeter wave frequencies,” European Microwave Conf., pp. 537-540, Sep. 2006. [5] Cheng-Ying Hsu, Chu-Yu Chen, and Huey-Ru Chuang, “A 60-GHz millimeter-wave bandpass filter using 0.18-μm CMOS technology,” IEEE Electron Device Letters, vol. 29, no. 3, pp. 246-248, Mar. 2008. [6] Cheng-Ying Hsu, Chu-Yu Chen, and Huey-Ru Chuang, “70 GHz folded loop dual-mode bandpass filter fabricated using 0.18μm standard CMOS technology,” IEEE Microwave Wireless Compon. Lett., vol. 18, no.9, pp. 587-589, Sep. 2008. [7] Hsin-Chia Lu, Chun-Sung Yeh, Shuan-An Wei, “Miniaturised 60 GHz rectangular ring bandpass filter in 90 nm CMOS technology,” Electronics Letters, vol. 47, no. 7, pp. 448-450, Mar. 2011. [8] Hsin-Chia Lu, Chun-Sung Yeh, Shuan-An Wei and Yien-Tien Chou, “60 GHz CPW dual-mode rectangular ring bandpass filter using integrated passive devices process,” in 2010 Asia-Pacific Microwave Conf., pp. 1883-1886, Dec. 2010. [9] 陳嘉緯,經由電容加載進行環型濾波器微型化,台灣大學碩士論文,民國97年。 [10] Zhewang Ma, Peng Cai, Xuehui Guan, Yoshio Kobayashi, and Tetsuo Anada, “A novel millimeter-wave ultra-wideband bandpass filter using microstrip dual-mode ring resonators loaded with open tuning stubs of different lengths,” in IEEE MTT-S Int. Microw. Symp. Dig., pp. 743-746, 2007. [11] S. S. Karthikeyan, Rakhesh Singh Kshetrimayum, “Performance enhancement of microstrip bandpass filter using CSSRR,” Advances in Computing, Control, and Telecommunication Tech., ACT '09, pp. 67-70, Dec. 2009. [12] Ajay Kumar Kunwer, Srikanta Pal, “High performance wide stopband lowpass filter using complementary split ring resonators as defected ground plane,” International Conference on Devices and Communications (ICDeCom), pp. 1-4, Feb. 2011. [13] IE3D, version 10.2, Zeland Corp, Freemont, CA. [14] William R. Eisenstadt and Yungseon Eo, “S-parameter-based IC interconnect transmission line characterization,” IEEE Trans. Comp., Hybrids, Manufact. Techol., vol.15, no.4, 483-490, Aug. 1992. | |
dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/63900 | - |
dc.description.abstract | 本論文分別在三個不同的製程實現三個60GHz的帶通濾波器,希望比較在不同製程下類似結構之效能,可提供系統設計者依實際需求做選擇。
本論文所使用的製程分別是Kyocera與達泰公司(現已併入達方電子)的低溫共燒陶瓷(low temperature co-fired ceramics, LTCC),以及Rogers公司的RO4003基板,皆採用矩形環狀結構來設計帶通濾波器,而為了達到有效抑制不同濾波器所產生零點之間的穿透係數,設計上需要較大的特徵阻抗,因此在低溫共燒陶瓷製程中的開槽傳輸線下方多加了下穿交叉線(underpass),進而提高傳輸線之高阻抗,而RO4003製程則不需要。接著進一步加上互補金屬開口諧振環(complementary single split ring resonator, CSSRR)以有效壓制基頻與二倍頻之間的穿透係數。 Kyocera的低溫共燒陶瓷製程串接濾波器最小插入損耗為1.2dB,低3dB頻率為50.9GHz,面積為3040μm×4997μm。達泰的低溫共燒陶瓷製程串接濾波器最小插入損耗為2.9dB,低3dB頻率為51.9GHz,面積為2745μm×5193μm。RO4003製程串接濾波器的最小插入損耗為1.91dB,3dB頻寬為54.8GHz,面積為3890μm×6540μm,含CSSRRs之串聯濾波器最小插入損耗為3.4dB,低3dB頻率為53.6GHz,面積為4060μm×7406μm。 主要的差別為此結構在低溫共燒陶瓷製程中用了三層介質層,且由於有開槽故在此下面加了下穿交叉線,以盡量避免訊號由開槽互相耦和而影響到原本的響應,但因為低溫共燒陶瓷為多層介質結構,剩下的介質厚度可能會產生水平方向的介質導波管(dielectric waveguide),故在低溫共燒陶瓷製程中的前後左右各加了連通柱牆(via wall),以確保訊號不會由其他方向以及透過開槽繞至下層介質而產生其他模態。而RO4003為單層介質板製程,其下面為空氣,因此不須加下穿交叉線及連通柱牆。 | zh_TW |
dc.description.abstract | This thesis presents the implementation of three 60GHz bandpass filters under three different processes. We will compare the performance of filters with similar structure under different processes. System designers can choose one depends on what he/she needs from these filters.
These processes are low temperature co-fired ceramics(LTCC) provided by Kyocera and DT Microcircuits and RO4003 substrate from Rogers. This thesis has implemented filters in two kinds of LTCC and RO4003 by using rectangular ring structure. To achieve higher impedance of open stubs for sufficient suppression of the transmission coefficient between four transmission zeros, slots must be used with underpass in LTCC to prevent unnecessary coupling. Filter using RO4003 does not need underpass, and CSSRR (complementary single split ring resonator) are added in the ground to suppress signal leakage between first and second resonance. The measured minimum insertion loss of cascaded-filter using Kyocera LTCC is 1.2dB, the filter size is 3040μm×4997μm. The measured minimum insertion loss of cascaded-filter using DT LTCC is 2.9dB, the filter size is 2745μm×5193μm. The measured minimum insertion loss of cascaded-filter and cascaded-filter with 3CSSRRs using RO4003 is 1.91 dB, 3.4dB respectively. The filter size is 3890μm×6540μm,3890μm×6540μm respectively. | en |
dc.description.provenance | Made available in DSpace on 2021-06-16T17:22:28Z (GMT). No. of bitstreams: 1 ntu-101-R99942090-1.pdf: 6421948 bytes, checksum: 6ed5d97cbb2995c98fef0e80948d3cbc (MD5) Previous issue date: 2012 | en |
dc.description.tableofcontents | 口試委員會審定書……………………………………………………………………#
摘要……………………………………………………………………………………i Abstract……………………………………………………………………………….iii 目錄……………………………………………………………………………..….…v 圖目錄………………………………………..…………...……………………..……ix 表目錄………………………………………………………...……..………….……xv 第一章 簡介 1 1.1 動機 1 1.2 相關研究發展現況 1 1.3 各章節介紹 6 第二章 矩形環狀濾波器設計理論 7 2.1 含 開路殘段之單一矩形環狀濾波器 7 2.1.1 含 開路殘段之矩形環狀濾波器 7 2.1.2 偶模態分析 8 2.1.3 奇模態分析 10 2.1.4 反射係數 12 2.1.5 穿透係數及傳輸零點 14 2.2 含 開路殘段之單一矩形環狀濾波器 15 2.2.1 偶模態分析 16 2.2.2 奇模態分析 18 2.2.3 穿透係數及傳輸零點 20 2.3 不同濾波器之零點比較 21 2.4 串接矩形濾波器 21 2.5 CSSRR 24 2.5.1 使用CSSRR於濾波器之原因 24 2.5.2 CSSRR物理尺寸之選擇 25 2.6 整合電路 27 第三章 模擬結果 29 3.1 使用Kyocera LTCC製程下之濾波器 29 3.1.1 含 開路殘段之矩形環狀濾波器 29 3.1.2 含 開路殘段之矩形環狀濾波器 34 3.1.3 串聯濾波器 38 3.2 使用DT LTCC製程之濾波器 39 3.2.1 含 開路殘段之矩形環狀濾波器 40 3.2.2 含 開路殘段之矩形環狀濾波器 43 3.2.3 串聯濾波器 46 3.3 使用RO4003製程之濾波器 48 3.3.1 含 開路殘段之矩形環狀濾波器 48 3.3.2 含 開路殘段之矩形環狀濾波器 50 3.3.3 串聯濾波器 52 3.3.4 含CSSRRs之串聯濾波器 54 第四章 量測方法及設置 60 4.1 TRL校準電路 60 4.2 Kyocera LTCC濾波器量測結果 62 4.3 DT LTCC基板濾波器量測結果 65 4.4 RO4003基板濾波器量測結果 69 第五章 比較與結論 81 | |
dc.language.iso | zh-TW | |
dc.title | 毫米波頻段利用不同開路殘段及互補金屬開口諧振環之寬阻帶矩形環狀濾波器 | zh_TW |
dc.title | A wide-stopband bandpass filter using dual-mode ring resonators loaded with open tuning stubs of different lengths and CSSRRs at millimeter wave band | en |
dc.type | Thesis | |
dc.date.schoolyear | 100-2 | |
dc.description.degree | 碩士 | |
dc.contributor.oralexamcommittee | 邱奕鵬(Yih-Peng Chiou),林坤佑(Kun-You Lin),曾昭雄 | |
dc.subject.keyword | 互補金屬開口諧振環,插入損耗, | zh_TW |
dc.subject.keyword | CSSRR,Insertion loss, | en |
dc.relation.page | 83 | |
dc.rights.note | 有償授權 | |
dc.date.accepted | 2012-08-16 | |
dc.contributor.author-college | 電機資訊學院 | zh_TW |
dc.contributor.author-dept | 電信工程學研究所 | zh_TW |
顯示於系所單位: | 電信工程學研究所 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-101-1.pdf 目前未授權公開取用 | 6.27 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。