請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/22103
標題: | 熱敏式微影技術製作「電極–碳管–電極」之電性量測平台 Fabrication of Metal-SWCNT-Metal Platforms for Electric Characterization by Thermal Scanning Probe Lithography |
作者: | Yu-Hsuan Cho 卓育萱 |
指導教授: | 陳俊顯(Chun-hsien Chen) |
關鍵字: | 熱敏式掃描探針微影,單壁奈米碳管,非彈性電子穿隧能譜, thermal scanning probe lithography,single-walled carbon nanotube,inelastic electron tunnelling spectroscopy, |
出版年 : | 2018 |
學位: | 碩士 |
摘要: | 分子電性量測平台以「電極-分子-電極」(metal-molecule-metal, MMM)系統為基本架構。過去以聚焦離子/電子束誘導金屬沉積法(focused ion/electron beam-induced deposition, FIBD/FEBID)製作金屬電極,但於選定的電極區域外圍會有少量金屬沉積,當兩電極外圍金屬互相重疊時,形成橋接電極間的漏電通路。本論文以熱敏式微影技術(thermal scanning probe lithography, t-SPL)為主軸,開發「鉑電極–單壁奈米碳管–鉑電極」(Pt-SWCNT-Pt)電性量測平台。T-SPL為利用加熱探針刻劃出固定形式圖案(well-defined pattern),相較於光學微影技術(photolithography)與電子束微影技術(e-beam lithography),具有下列三個優點:(1)無光罩微影技術、(2)常壓環境下操作、(3)解析度小於10 nm。本實驗於已沉積單壁奈米碳管之元件,以旋轉塗佈的方式將兩層特定光阻附著於元件,上下層光阻材料分別為聚鄰苯二甲醯胺(polyphthalamide, PPA)及聚二甲基戊醯胺(polydimethylglutarimide, PMGI)。當加熱探針接觸到光阻表面,PPA受熱分解成易揮發的單體化合物,藉此刻劃單壁奈米碳管兩端的電極圖案,過程迅速約1至3分鐘。接著將晶片浸泡蝕刻液將裸露的PMGI去除,再利用物理氣相沉積鉑金屬,舉離(lift-off)去除光阻後即可得到Pt-SWCNT-Pt系統。本論文聚焦於元件開發及非彈性電子穿隧能譜:(1)為使熱阻式原子力顯微鏡能在塗佈光阻的元件觀察到單壁奈米碳管,使用低濃度的PPA溶液使光阻膜厚變薄,但蝕刻過程時對需保留PMGI區域保護力下降;提高PPA濃度能保護PMGI不被侵蝕,但光阻太厚無法觀察到單壁奈米碳管。最適條件為20 nm的PMGI及20 nm PPA。(2)量測鉑導線電阻並計算電阻率為4.11 X 10–6 Ωcm,遠低於以FIBD/FEBID製作鉑導線之電阻率。(3)得到Pt-SWCNT-Pt的電阻為9.5 kΩ,符合文獻報導中奈米單壁奈米碳管的電阻。並且在4.2 K下量測非彈性電子穿隧能譜(inelastic electron tunneling spectroscopy, IETS),觀測到類石墨物質的C-C鍵振動譜峰(G band, ~1600 cm–1)。 The study on molecular electronic properties is based on Metal-Molecule-Metal (MMM) junctions. Common method for fabricating MMM junctions such as focused ion/electron beam-induced deposition (FIBD/FEBID) is not ideal due to metal-halo which may result in short circuit. Herein, Pt-SWCNT (single-walled carbon nanotube)-Pt platforms were fabricated by thermal scanning probe lithography (t-SPL). T-SPL uses heated probe to define the pattern. A dedicated t-SPL instrument is NanoFrazor which is thermal atomic force microscopy probe. First, two-layer polymers were spin coated on wafer which has been deposited SWCNTs. The base layer is polymethylglutarimide (PMGI) and top layer is polyphthalaldehyde (PPA). The probe of NanoFrazor can be heated to 1000 0C. When the hot probe is brought into contact with surface, PPA decomposes and evaporates locally. Therefore, we pattern the both ends of SWCNT for electrodes. The time of this process is about 1-3 minutes. Next, using developer to dissolve the bare PMGI. Subsequently, deposit Pt by physical vapor deposition (PVD) and then lift off unwanted region of Pt. This study focuses on fabrication of Pt-SWCNT-Pt platforms by t-SPL technique. (1) To scan the SWCNT which under the two-layer polymers by AFM, decreasing the concentration of PPA for thinner film; however, low concentration of PPA result in the PMGI being over-etching. The 20 nm PMGI and 20 nm PPA are appropriate conditions. (2) The resistivity of Pt wire is 4.11 X 10–6 Ωcm which is lower than that fabricated by FIBD/FEBID. (3) The resistance of Pt-SWCNT-Pt is 9.5 kΩ which consistent with previous work. Furthermore, the IETS (inelastic electron tunnelling spectroscopy) signal of SWCNT are detected. |
URI: | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/22103 |
DOI: | 10.6342/NTU201802559 |
全文授權: | 未授權 |
顯示於系所單位: | 化學系 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-107-1.pdf 目前未授權公開取用 | 6.74 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。