請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/19138
完整後設資料紀錄
DC 欄位 | 值 | 語言 |
---|---|---|
dc.contributor.advisor | 潘永寧(Yung-Ning Pan) | |
dc.contributor.author | Yi-Chen Lai | en |
dc.contributor.author | 賴易辰 | zh_TW |
dc.date.accessioned | 2021-06-08T01:46:22Z | - |
dc.date.copyright | 2016-09-13 | |
dc.date.issued | 2016 | |
dc.date.submitted | 2016-08-10 | |
dc.identifier.citation | [1] 吳漢宗、楊智超,“材料手冊─非鐵金屬材料”,中國材料學學會,1983,p. 25。
[2] JIS Handbook, “Non-Ferrous Materials and Metallurgy”, Japanese Standards Association, 1987-88. [3] John E. Gruzleski, Bernard m. Closset, “The Treatment of Liquid Aluminum-Silicon Alloys”, The American Foundrymen’s Society, 1990. [4] D. L. Zalensas, “Aluminum Casting Technology”, 2nd Edition, AFS, 1993. [5] H. Ye, “An Overview of the Development of Al-Si-Alloy Based Material for Engine Applications, ” Journal of Materials Engineering and Performance, 2003, Vol. 12, p. 288. [6] E. N. Pan, S. W. Lin and P. C. Yu, “Improvement in Gravity-Segregation of Primary Silicon in Hyper-Eutectic Al-Si Alloys,”AFS Trans., Vol. 115, 2007, pp.167-176. [7] F. C. Robles Herna’ndez and J.H. Sokolowski, “Novel Image Analysis to Determine the Si Modification for Hypoeutectic and Hypereutectic Al-Si Alloys,” Journal of the Minerals, Metals and Materials Society, 2005, Vol. 57, p. 48. [8] 陳武宏,“鑄鋁技術”,全華科技圖書,民國79年。 [9] C. R. Ho and B. Cantor, “Heterogeneous Nucleation of Solidification of Si in Al-Si and A1-Si-P Alloys,” Acta Metallurgica et Materialia, 1995, Vol. 43, p. 3231. [10] B. Cantor, “Impurity Effects on Heterogeneous Nucleation,” Materials Science and Engineering A, 1997, A226-228, p. 151. [11] H. Lescuyera, M. Allibertb and G. Laslaza , “Solubility and Precipitation of AlP in Al-Si Melts Studied with A Temperature Controlled Filtration Technique,” Journal of Alloys and Compounds, Vol. 279, 1998, p. 237. [12] D.A. Porter and K.E. Eastering, ‘‘Phase Transformations in Metals and Alloys’’, Chapman & Hall, 1992, p. 185. [13] M. Garat and R. Scalliet, ‘‘A Review of Recent French Casting Alloy Development,’’ AFS Trans., Vol. 86, 1978, pp.549-562. [14] G. K. Sigworth, ‘‘Theoretical and Practical Aspects of the Modification of Al-Si Alloy,’’ AFS Trans., Vol. 91, 1983, pp.7-16. [15] C. B. Kim and R. W. Heine, ‘‘Fundamentals of Modification in the Aluminum-Silicon System,’’ J. Inst. Metals, Vol. 92, 1964, pp.367-376. [16] N. Tenekedjiev, D. Argo and J. E. Gruzleski, “Sodium, Strontium and Phosphorus Effects in Hypereutectic Al-Si Alloys,” AFS Trans., Vol. 97, 1989, pp.127-136. [17] G. K. Sigwoth, “Refinement of Hypereutectic Al-Si Alloys,” AFS Trans., Vol. 95, 1987, pp. 303-314. [18] 邱弘興,“A390鋁合金之矽型態控制及其與機械性質之關係”,國科會85年研究計劃報告。 [19] H. T. Zhang, K. S. Zuo, X. Han, B. Shao, K. Qin and J. Z. Cui, ‘‘Effects of P+Cr Complex Modification and Solidification Conditions on Microstructure of Hypereutectic Al-Si Alloys by Wedge-shaped Copper Mould Casting,’’ China Foundry, Vol. 11, 2014, pp.481-486. [20] 左克生,“過共晶Al-Si合金凝固組織研究”,東北大學碩士論文,2012。 [21] D. Apelian, G. K. Sigworth, and K. R. Whaler, ‘‘Assessment of Grain Refining and Modification of Al-Si Foundry Alloys by Thermal Analysis,’’ AFS Trans., Vol. 92, 1984, pp.297-307. [22] B. Chamberlin and V. J. Zabek, ‘‘Reappraisal of the Tensile Properties of Al-Si-Mg Casting Alloys,’’ AFS Trans., Vol. 81, 1973, pp.322-327. [23] R. Sharan and N. P. Saksena, ‘‘Rare Earth Addition as Modifiers of Aluminum-Silicon Alloy,’’ AFS International Casting Metals Journal, No.1, Vol. 3, 1978, pp.29-33. [24] Z. Qiyun, Z. Chaogui and H. Wanshu, ‘‘The Modification of Al-Si Eutectic Alloys with Rare-Earth Elements,’’ Acta Metallurgical Sinica, Vol. 17, 1981, pp.130-136. [25] B. J. Ye, C. R. Loper, Jr., D. Y. Lu and C. S. Kang, ‘‘An Assessment of the Role of Rare Earth in the Eutectic Modification of Casting Aluminum-Silicon Alloys,’’ AFS Trans., Vol. 93, 1985, pp.533-544. [26] K. Alker and U. Hislscher, ‘‘Experiences with the Permanent Modification of Al-Si Casting Alloys,’’ Aluminum, Vol. 48, 1972, pp.362-367. [27] H. Fredriksson, M. Hillert and N. Lange, ‘‘The Modification of Aluminum-Silicon Alloys by Sodium,’’ J. Inst. Metals, Vol. 101, 1973, pp.285-299. [28] F. Fommei, ‘‘Modification Treatments of Al-Si Alloys,’’ Alumino, Vol. 46, 1977, pp.121-135. [29] J. R. Denton and J. A. Spittle, ‘‘Solidification and Susceptibility to Hydrogen Adsorption of Al-Si Alloys Containing Strontium,’’ Materials Science and Technology, Vol. 1, 1985, pp.305-311. [30] H. Shahani, ‘‘Effect of Hydrogen on the Shrinkage Porosity of Aluminum Copper and Aluminum Silicon Alloys,’’ Scandinavian Journal of Metallurgy, Vol. 14, 1985, pp.306-312. [31] B. Closset and J. E. Gruzleski, ‘‘Mechanical Properties of A356.0 Alloys Modified with Pure Strondium,’’ AFS Trans., Vol. 90, 1982, pp.453-464. [32] L. Backerud, G. Chai and J. Tamminen, “Solidification Characteristics of Aluminum Alloys,” Vol. 2: Foundry Alloys, 1990, pp. 119-126. [33] J. Campbell, ‘‘Feeding Mechanisms in Castings,’’ AFS Cast Metal Res. Journal, Vol.5, 1969, No.1, pp.1-8. [34] 陳建興,“A356鑄造鋁輪圈之製程評估及品質改善”,國立台灣大學機械工程研究所碩士論文,民國86年。 [35] 顏進豐,“凝固熱參數與A356鋁合金品質之相關性研究”,國立台灣大學機械工程研究所碩士論文,民國87年。 [36] 林文和、邱傳聖,“鑄造學”,高立圖書,pp. 260-264,民國81年。 [37] 龔肇鑄,“鑄造學”,文京圖書,民國74年。 [38] F. P. Bowdon, D. T., “The Friction and Lubrication of Solids Part II”, Oxford University Press, 1964. [39] 莊東漢,“材料破損分析”,五南圖書,2007,pp. 281-338。 [40] 王盈琁,“添加合金元素對 Al-17%Si 合金高溫機械性質之影響”,大同大學材料工程研究所論文,民國99年。 [41] 陳擷安,“A390過共晶鋁矽合金之初晶矽偏析行為及耐磨耗性研究”,國立台灣大學機械工程研究所碩士論文,民國104年。 [42] H. Kattoh, “Critical Temperature for Grain Refine of Primary Si in Hyper-eutectic Al-Si Alloy with Phosphorus Addition, ”Journal of Japan Institute of Light Metals, Vol. 52, 2002, p. 18. [43] 賴耿陽,“鑄造技術十-特殊鑄造技術”,復興書局,pp. 216-217,民國88年。 | |
dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/19138 | - |
dc.description.abstract | A390過共晶鋁矽合金在重力鑄造時,由於矽的比重(2.33g/cm3)較鋁 (2.74 g/cm3)低,因此在凝固過程中容易產生初晶矽(primary silicon)上浮的現象,而使得同一鑄件在不同位置的機械性質不一致。本研究係利用矽與鋁比重之差異,以一自行設計之旋轉裝置進行A390鑄造,使得A390之凝固過程在旋轉狀態下受到一穩定離心力作用,促使比重較低、硬度較高的初晶矽產生顯著的徑向偏析,往旋轉軸中心側聚集,預期鑄件在該局部位置能得到較高比例的初晶矽分佈,進而達到提升耐磨耗性之效果。本研究在固定轉速150 rpm(重力倍數約10 G)之離心鑄造條件下,探討P之細化處理(針對初晶矽)、Sr之調質處理(針對共晶矽)以及P+Cr複合細化處理(針對初晶矽)等三種不同熔液處理對於A390過共晶鋁矽合金之顯微組織及耐磨耗性之影響,最後利用迴歸分析以獲致各參數與耐磨耗性之間的關係。
實驗結果顯示,所有經離心鑄造之A390鑄件其耐磨耗性皆以內側(接近旋轉軸中心)為最佳,符合本研究之預期結果(以離心鑄造提升A390初晶矽集中處之耐磨耗性)。對於細化A390之初晶矽而言,以0.02%P之細化劑、持溫5分鐘,其細化效果最佳,可使初晶矽平均尺寸由96µm降低至43µm,且單獨添加含P之細化劑其細化效果優於P + Cr之複合細化劑;在調質共晶矽方面,添加0.02%Sr調質劑後,須持溫10分鐘以上方能完全發揮其調質效果,共晶矽平均調質級數可達AFS 4~5級。所有爐次中以添加0.02%P之細化劑、持溫5分鐘之細化處理所獲離心鑄件內側之耐磨耗性為最佳,其耐磨耗性較未施以任何處理、Sr調質處理以及P+Cr複合細化處理等均佳,且較未處理之A390重力鑄件上層提升約2倍。另外,對於影響耐磨耗性之各參數作綜合迴歸分析,由迴歸分析結果可知:當初晶矽面積率愈高、初晶矽顆粒尺寸愈小、共晶矽調質效果愈佳及孔洞面積率愈低,則耐磨耗性愈佳。 | zh_TW |
dc.description.abstract | While casting the A390 hypereutectic alloy, primary Si particles tend to float to the upper part of the casting due to the difference in specific weight between primary Si particles and the aluminum bulk liquid, the so-called gravity segregation. As a result, the microstructures and the mechanical properties in different parts of the casting vary. This research utilized the above-mentioned phenomenon of the primary Si gravity segregation, and further to enhance this segregation nature by employing centrifuging casting process to achieve better wear resistance in specific area of the castings. A centrifuging casting apparatus was constructed which allows the casting to be solidified under the centrifugal force. Under the centrifuging casting condition, the primary Si particles which have low specific gravity and high hardness tend to move toward the rotational axis and aggregate at the inner portion of the castings, and thus to enhance the wear resistance of the A390 alloy. In addition, P refinement (for primary Si), Sr modification (for eutectic Si) and P + Cr refinement (for primary Si) of A390 alloy were performed to examine the effects of these different melt treatments on the microstructures and wear resistance property of the centrifuging castings at the rotational speed of 150 rpm (~10G). Further, the relationship between the microstructure features obtained and the wear resistance property was evaluated.
The microstructure of the A390 alloy without any treatments exhibits somewhat large primary Si particles with an average size of around 96μm, and acicular type eutectic Si of class 1. When the alloy was refined with an appropriate amount of P, i.e., 0.02%P, the size of the primary Si was substantially reduced to around 43μm, while the eutectic Si remained more or less unchanged. In addition, when the alloy was refined with various combinations of P and Cr, no beneficial effect in reducing the size of the primary Si particle was found. Instead, a slight increase in primary Si size was obtained, with the average size being increased to around 65μm. On the other hand, when the alloy was modified by 0.02%Sr, even though the eutectic Si was improved to class 4-5, the primary Si was coarsened significantly to around 250μm. Furthermore, the effects of the microstructure features on the wear resistance property of A390 alloy was studied, and regression analyses were performed by looking into the correlations between the four main dependent variables, namely, the area ratio of the primary Si (X, %), the average primary Si size (Y, μm), degree of eutectic Si modification (Z, class), and the % porosity (C, %), and the wear rate (W, mm3/m). The obtained regression equation is: W = 0.029245 – 0.00098X + 0.000045Y – 0.00347Z + 0.001448C. The analysis results indicate that the wear rate can be reduced by increasing area ratio of the primary Si, decreasing primary Si size, increasing degree (class) of eutectic Si modification, and reducing % porosity. | en |
dc.description.provenance | Made available in DSpace on 2021-06-08T01:46:22Z (GMT). No. of bitstreams: 1 ntu-105-R03522726-1.pdf: 8816139 bytes, checksum: c6abfc4c5511590b494c29e8a71c4a2e (MD5) Previous issue date: 2016 | en |
dc.description.tableofcontents | 誌謝 i
中文摘要 ii ABSTRACT iv CONTENTS vii LIST OF TABLES ix LIST OF FIGURES x 第1章 前言 1 第2章 文獻探討 3 2.1 鋁矽合金簡介 3 2.1.1 鋁矽合金的特性 3 2.1.2 A390過共晶鋁矽合金 4 2.1.3 初晶矽及其細化處理(Refinement) 5 2.1.4 共晶矽及其調質處理(Modification) 6 2.2 鋁合金鑄件中的孔洞 9 2.2.1 縮孔的形成 9 2.2.2 氣孔的形成 10 2.3 浮力原理 - 阿基米德定律 11 2.4 離心鑄造法 12 2.5 磨耗行為 13 2.5.1 磨耗概論 13 2.5.2 磨耗機制 13 2.5.3 影響磨耗行為之參數 15 第3章 實驗方法與步驟 27 3.1 實驗目的 27 3.2 實驗設計 27 3.3 旋轉裝置 28 3.4 鑄件模型 29 3.5 熔煉與澆鑄 29 3.6 試片取樣 31 3.7 顯微組織觀察 31 3.7.1 初晶矽之面積率量測 31 3.7.2 孔洞之面積率量測 32 3.7.3 共晶矽調質效果量化 32 3.7.4 初晶矽尺寸量測 33 3.8 耐磨耗試驗 33 第4章 結果與討論 41 4.1 顯微組織觀察 41 4.1.1 爐次G (未處理、重力鑄造) 41 4.1.2 爐次A (未處理、離心鑄造) 41 4.1.3 爐次B (0.02%P初晶矽細化處理、離心鑄造) 42 4.1.4 爐次C-1、C-2、C-3 (0.02%Sr共晶矽調質處理、離心鑄造) 42 4.1.5 爐次D-1、D-2、D-3 (P+Cr初晶矽複合細化、離心鑄造) 46 4.1.6 小結 48 4.2 耐磨耗性能 49 4.2.1 耐磨耗試驗結果 49 4.2.2 各種不同參數對於A390耐磨耗性之影響 51 第5章 結論 73 第6章 參考文獻 76 | |
dc.language.iso | zh-TW | |
dc.title | 離心加壓力及熔液處理對於A390過共晶鋁矽合金之顯微組織及耐磨耗性之影響 | zh_TW |
dc.title | Effects of Centrifuging Force and Melt Treatment on the Microstructure and Wear Resistance Property of A390 hyper-eutectic Al-Si Alloy | en |
dc.type | Thesis | |
dc.date.schoolyear | 104-2 | |
dc.description.degree | 碩士 | |
dc.contributor.oralexamcommittee | 許正勳(Cheng-Hsun Hsu),楊智富(Chih-Fu Yang) | |
dc.subject.keyword | A390,離心加壓力,初晶矽偏析,細化處裡,共晶矽調質處理,耐磨耗性, | zh_TW |
dc.subject.keyword | A390,Centrifuging force,Primary Si segregation,Refinement,Eutectic Si modification,Wear resistance property, | en |
dc.relation.page | 79 | |
dc.identifier.doi | 10.6342/NTU201600842 | |
dc.rights.note | 未授權 | |
dc.date.accepted | 2016-08-10 | |
dc.contributor.author-college | 工學院 | zh_TW |
dc.contributor.author-dept | 機械工程學研究所 | zh_TW |
顯示於系所單位: | 機械工程學系 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-105-1.pdf 目前未授權公開取用 | 8.61 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。