Skip navigation

DSpace

機構典藏 DSpace 系統致力於保存各式數位資料(如:文字、圖片、PDF)並使其易於取用。

點此認識 DSpace
DSpace logo
English
中文
  • 瀏覽論文
    • 校院系所
    • 出版年
    • 作者
    • 標題
    • 關鍵字
  • 搜尋 TDR
  • 授權 Q&A
    • 我的頁面
    • 接受 E-mail 通知
    • 編輯個人資料
  1. NTU Theses and Dissertations Repository
  2. 工學院
  3. 材料科學與工程學系
請用此 Handle URI 來引用此文件: http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70979
標題: 3D列印銅基合金之材料性質分析與擠出模擬
Analysis of Material Properties of Copper-Based Alloy by 3D Printing and Modelling of Melt-Extrusion (ME)
作者: Yi-Ting Huang
黃怡婷
指導教授: 韋文誠(Wen-Cheng Wei)
關鍵字: 銅合金,線材,磨耗率,硬度,EDS,全定量分析,模擬,
Cu-alloy,wire,wear rate,hardness,EDS,Quantitative analysis,simulation,
出版年 : 2018
學位: 碩士
摘要: 本研究採用前[1,2]設計開發的一種熔融擠出裝置,使用能在<1300 oC熔融之銅基合金進行智慧模具的3D列印,分析材料之相關性質,因此,研究目標放在該合金材料之硬度、耐磨性及成分之分析與進行熱擠出需要之作用力之探討。研究結果顯示,硬度特性方面,在相同熱處理條件下,銅9鎳6錫(硬度269 HV )明顯優於其他三種銅基合金,而銅6鎳2鋁合金(硬度237 HV )則次之,該硬度已高於以表層鍍鎳之鑰匙作為目標的硬度(207 HV )。後續研究以銅9鎳6錫為主要研究之材料,銅6鎳2鋁為備案。在接觸磨耗方面,測試結果符合硬度越高磨耗率越低之預期,呈線性(反比)關係。在成分之分析方面,利用能量散布光譜( Energy-dispersive X-ray spectroscopy,EDS)進行全定量成分分析,分析之技術利用銅6鎳2鋁做為標準樣品進行校正,用於分析線材或列印樣品的成分均勻性, 銅11鎳之平均分析結果顯示誤差值(standard deviation)在0.2 %以內。另一方面,藉由在室溫環境下模擬金屬高溫熔融擠出,在0.4 ~ 0.2 mm噴口的條件時,藉由量測四個作用力,了解高黏度(熔融玻璃)及銅金屬熔湯在氧化鋁噴嘴內之流變行為。
This study adapts a melt extrusion module [1, 2], which was designed and developed by our group, selects Cu-base alloys capable of melting at <1300 oC, and has conducted 3D printing to make smart mold in previous study. Therefore, this research objectives are to investigate the hardness, wear resistance and compositional uniformity of Cu-based alloys, and the forces required for the melt extrusion. The results show that the hardness (269 HV) of annealed Cu-9Ni-6Sn is obviously superior to Cu-6Ni-2Al (237 HV) and the surface hardness (207 HV) of Ni-coated key. In contact wear, the higher the hardness of the alloys, the lower the wear rate. The relationship between hardness and wear rate is inversely linear behavior. A quantification analysis of the chemical composition of the wires used for 3D printing used Energy-dispersive X-ray spectroscopy (EDS) for the analysis. The standard deviation for the Ni in Cu-11Ni test is less than 0.2 %. Finally, the melting extrusion simulation of high temperature melt Cu alloy is conducted with 0.4 ~ 0.2 mm nozzle size. The required 4 forces against the frictions coming from the tube wall and the nozzle were considered. The simulation results resolve the flowing behavior of high viscous glass and melt Cu-alloy in Al2O3 nozzle through smaller nozzles.
URI: http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/70979
DOI: 10.6342/NTU201802080
全文授權: 有償授權
顯示於系所單位:材料科學與工程學系

文件中的檔案:
檔案 大小格式 
ntu-107-1.pdf
  目前未授權公開取用
12.38 MBAdobe PDF
顯示文件完整紀錄


系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。

社群連結
聯絡資訊
10617臺北市大安區羅斯福路四段1號
No.1 Sec.4, Roosevelt Rd., Taipei, Taiwan, R.O.C. 106
Tel: (02)33662353
Email: ntuetds@ntu.edu.tw
意見箱
相關連結
館藏目錄
國內圖書館整合查詢 MetaCat
臺大學術典藏 NTU Scholars
臺大圖書館數位典藏館
本站聲明
© NTU Library All Rights Reserved