Please use this identifier to cite or link to this item:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/58795Full metadata record
| ???org.dspace.app.webui.jsptag.ItemTag.dcfield??? | Value | Language |
|---|---|---|
| dc.contributor.advisor | 張正憲(Jeng-Shian Chang) | |
| dc.contributor.author | Shih-Wei Huang | en |
| dc.contributor.author | 黃士瑋 | zh_TW |
| dc.date.accessioned | 2021-06-16T08:31:27Z | - |
| dc.date.available | 2017-03-18 | |
| dc.date.copyright | 2014-03-18 | |
| dc.date.issued | 2013 | |
| dc.date.submitted | 2013-12-24 | |
| dc.identifier.citation | 1.F.Amirouche,Y. Zhou, and T. Johnson, 2009.'Current micropumptechnologies and their biomedical applications,'Microsystem Technologies-Micro-and Nanosystems-Information Storage and Processing Systems, 15(5): pp. 647-666
2.B.D.Iverson, and S.V. Garimella, 2008.'Recent advances in microscale pumping technologies: a review and evaluation,' Microfluidics and Nanofluidics, 5(2): pp. 145-174. 3.A.Nisar, Ntin Afzulpurkar,Banchong Mahaisavariya,Adison Tuantranont,2008.'MEMS-based micropumps in drug delivery and biomedical applications,' Sensors and Actuators B-Chemical,130(2): pp. 917-942. 4.N.C.Tsai, and C.Y. Sue, 2007.'Review of MEMS-based drug delivery and dosing systems,' Sensors and Actuators a-Physical,134(2): pp. 555-564. 5.C.S.Zhang ,D. Xing, and Y.Y. Li,2007.'Micropumps, microvalves, and micromixers within PCR microfluidic chips: Advances and trends,'Biotechnology Advances, 25(5): pp. 483-514. 6.A.Olsson, G. Stemme, and E. Stemme,1995.' A valve-less planar fluid pump with two pump chambers,'Sensors and Actuators a-Physical, 47(1-3): pp. 549-556. 7.E.Stemme, and G. Stemme, 1993.'A valveless diffuser/nozzle-based fluid pump,' Sensors and Actuators a-Physical,39(2): pp. 159-167. 8.S.Lee, and K.J. Kim, 2006.'Design of IPMC actuator-driven valve-less micropump and its flow rate estimation at low Reynolds numbers,'Smart Materials & Structures, 15(4): pp. 1103-1109. 9.M.A.Gretillat, F. Gretillat, and N.F. de Rooij,1999.' Micromechanical relay with electrostatic actuation and metallic contacts,'Journal of Micromechanics and Microengineering,9(4): pp. 324-331. 10.A.Machauf, Y. Nemirovsky, and U. Dinnar, 2005.' A membrane micropump electrostatically actuated across the working fluid,'Journal of Micromechanics and Microengineering, 15(12): pp. 2309-2316. 11.R.Linnemann,P.Woias, C.D.Senfft, J.A.Ditterich,1998.'A self-priming and bubble-tolerantpiezoelectric silicon micropump for liquids and gases,' 12.T.R.Pan, Scott J McDonald,Eleanor M Kai,Babak Ziaie, 2005.'A magnetically driven PDMS micropump with ball check-valves,' Journal of Micromechanics and Microengineering,15(5): pp. 1021-1026. 13.C.J.Hsu, and H.J. Sheen,2009.'A microfluidic flow-converter based on a double-chamber planar micropump,'Microfluidics and Nanofluidics,6(5): pp. 669-678. 14.T.T.Bringley,C.Stephan,V.Nicolas,Z.Jun,2008.'An experimental investigation and a simple model of a valveless pump,' Physics of Fluids,20(3). 15.A.S.Forouhar,M.Liebling,A.Hickerson,AbbasNasiraei-Moghaddam,H.J.Tsai,JayR.Hove,ScottE.Fraser,MaryE.Dickson,Morteza Gharib,2006.'The embryonic vertebrate heart tube is a dynamic suction pump,' Science,312(5774): pp. 751-753. 16.A.Olsson,P.Enoksson,G.Stemme,E.Stemme,1997.'Micromachined flat-walled valveless diffuser pumps,' Journal of Microelectromechanical Systems,6(2): pp. 161-166. 17.李俊賢, 可攜式無閥壓電微幫浦之設計製作與應用. 國立台灣大學應用力學研究所碩士論文, 2003. 18.謝明哲, 無閥式微幫浦之腔體設計與作動機制研究. 國立台灣大學應用力學研究所碩士論文, 2009. 19.Teng Yong Ng, D.X., Khin Yong Lam.,2005.United state patent (Patent No.: US 6910869), Institute of High Performance Computing, Singapore. 20.J.S.Yoon, J.W.Choi, I.H.Lee, M.S.Kim,2006.'A valveless micropump for bidirectional applications,'Sensors and Actuators a-Physical, 135(2): pp. 833-838. 21.I.Izzo, D.Accoto, A.Menciassi, L.Schmitt, P.Dario, 2007.'Modeling and experimental validation of a piezoelectric micropump with novel no-moving-part valves,'Sensors and Actuators a-Physical, 133(1): pp. 128-140. 22.C.J.Lee,et al.,2009. 'A study of PZT valveless micropump with asymmetric obstacles,'MicrosystemTechnologies-Micro-andNanosystems-Information Storage and Processing Systems,15(7): pp. 993-1000. 23.A.Olsson, G. Stemme, and E. Stemme,2000.' Numerical and experimental studies of flat-walled diffuser elements for valve-less micropumps,'Sensors and Actuators, Vol.84: pp. 165-175. 24.B.Fan, , G. Song, and F. Hussain, 2005.'Simulation of a piezoelectrically actuated valveless micropump,'Smart Materials & Structures,Vol.14: pp. 400-405. 25.L.S.Pan , T.Y. Ng, X.H. Wu, and H.P. Lee,2003. ' Analysis of valveless micropumps with inertial effects,' Journal of Micromechanics and Microengineering, Vol.13: pp. 390-399. 26.A.Ullmann , 1998. 'The piezoelectric valve-less pump-performance enhancement analysis,' Sensors and Actuators a-Physical,69(1): pp.97-105. 27.K.S.Yang , I.Y. Chen, and C.C. Wang,2006.'Performance of nozzle/diffuser micro-pumps subject to parallel and series combinations,'Chemical Engineering & Technology, 29(6): pp. 703-710. 28.A.Olsson, G. Stemme, and E. Stemme,1999.'A numerical design study of the valveless diffuser pump using a lumped-mass model,'Journal of Micromechanics and Microengineering,9(1): pp.34-44. 29.ANSYS CFX 12.1 User Manuals. 30.CFDRC V2004 User Manuals. 31.林家祥, 進出口設計對無閥式微幫浦效能影響之數值模擬. 國立台灣大學應用力學研究所碩士論文, 2011. 32.蔡文惠, 進出口設計對無閥式微幫浦效能影響之實驗探討. 國立台灣大學應用力學研究所碩士論文, 2010. 33.Documentation for ANSYS: Coupled Field Analysis Guide. 34.Ha Dong-Ho, et al.,2009.'Three-dimensional electro-fluid-strectural interaction simulation for pumping performance evaluation of a valveless micropump,'Smart Materials & Structures,18(4): pp. 15-22. 35.T.T.Nguyen, and N.S. Goo,2006. 'A Novel PDMS valveless micropump with a circular lightweight piezo-composite actuator,'Key Engineering Materials,321-323: pp. 245-248. 36.陳柏維, 進出口的夾角設計對無閥式微幫浦效能影響之數值模擬. 國立台灣大學應用力學研究所碩士論文, 2012. | |
| dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/58795 | - |
| dc.description.abstract | 本文利用商業軟體ANSYS作為數值模擬的工具，對噴嘴/擴散器式的壓電無閥式微幫浦作數值模擬分析，藉由改變振動腔設計，以及改變振動腔與進出口層的厚度，探討其對微幫浦性能的影響。除了比對實驗的流量之外，同時將模擬計算出的流場與實驗上的流場顯影作比較與討論，以對微幫浦內流場變化對於流量的影響有更清楚的交代。
與一般常用的模擬微幫浦之方法不同，本文的模型沒有經過簡化，而是考慮壓電材料與微幫浦之間的電、流、固多重耦合分析。本文處理流固耦合所使用的模擬計算方法也有別於一般CFD軟體的移動邊界(moving boundary)，而是透過ANSYS與ANSYS CFX將結構場與流場結合的同步雙向耦合，比起一般的移動邊界法，本文所得到的流場更為擬真且可信。 由數值計算結果可以發現，當振動腔設計為雙心型時會有最佳的流量。儘管模擬的流量數值誤差稍大，流量變化的趨勢仍然和實驗大致相符。另外，模擬結果也可以看出將振動腔上層厚度改變對流量確實有所影響，當振動腔上層厚度為1mm時，圓型腔體會有最佳流量；當振動腔與進出口層的厚度為0.5mm時，雙心腔體會有最佳流量。 | zh_TW |
| dc.description.abstract | This paper used the ANSYS software to do numerical analysis of efficiency for the valveless nozzle/diffuser-based micropump. By designing the chamber, and changing the thickness of layer of chamber and inlet and outlet to the micropump in order to discuss its influence on the pumping effiency.This paper not only compared the flow rate between simulations and experiments, but also discussed and analyzed the simulation fluid field with experimental results,in order to know more detailed explanation of the fluid mechanism.
Unlike the common method in the simulation of micropump, the simulating model in this paper is established to be more completeby considering piezoelectric materials, the structure of micropump, and the flow field in all.The general CFD software processes fluid-structure interaction by using moving boundary method.Instead of moving boundary method, this paper used ANSYS and ANSYS CFX for the structural and fluid domains, respectively. Both the structural and fluid domains are coupled in the three-dimensional simulation. The simulation results are closer to reality than the moving boundary. According to the result of the simulations, we found that when designing the chamber of double-heart, the flow rate was more efficient than others.Although ,there are some errors between the simulation and experimental results,the trends of flow rate between simulations and experiments are quiet similar.In addition,simulation results also showed that changed the thickness of layer of chamber and inlet and outlet had influence on the pumping effiency.When the thickness of upper layer of chamber was 1mm, the flow rate was the best for the circle pump. When the thickness of upper layer of chamber was 0.5mm, the flow rate was optimal for the double-heart pump. | en |
| dc.description.provenance | Made available in DSpace on 2021-06-16T08:31:27Z (GMT). No. of bitstreams: 1 ntu-102-R00543048-1.pdf: 7280526 bytes, checksum: 17bd12bf95a9088671c97b10ba3f46fa (MD5) Previous issue date: 2013 | en |
| dc.description.tableofcontents | 摘要 I
ABSTRACT Ⅱ 目錄 III 圖與表目錄 V 第一章 導論 1 1.1 前言 1 1.2 文獻回顧 2 1.2.1 驅動方式簡介 2 1.2.2 微閥門簡介 3 1.2.3無閥式微幫浦之文獻回顧 4 1.2.4 無閥式微幫浦之數值模擬文獻回顧 5 1.3 研究動機 7 第二章理論基礎 8 2.1 無閥式微幫浦基本工作原理 8 2.2 噴嘴/擴散器理論分析 9 2.3 壓電、結構、流體之相互耦合作用分析 12 2.3.1 壓電與結構耦合 12 2.3.2壓電與結構耦合之邊界條件 13 2.3.3流場與結構耦合 13 2.3.4流場與結構耦合之邊界條件 14 第三章 數值方法與模擬設定 15 3.1 數值方法 16 3.1.1 有限體積法 16 3.1.2 收斂標準 18 3.2 實驗模型與模擬設定 19 3.2.1 模擬模型基本設定 19 3.2.2 模擬基本假設 21 3.2.3 模擬參數設定 22 第四章模擬結果與討論 23 4.1 不同振動腔設計之數值模擬結果 23 4.1.1 實驗流量與模擬計算流量之比較分析 23 4.1.2 壓電片位移模擬 24 4.1.3 流量與共振頻之誤差分析 24 4.1.4 雙心振動腔設計與圓型振動腔設計之流場分析 25 4.1.5 前心腔與後心腔在共振頻時之流場分析 26 4.1.6 不同振動腔設計在共振頻時之腔體內壓力分析 27 4.2 振動腔與進出口層厚度改變之數值模擬結果 28 4.2.1 振動腔與進出口層厚度(Zu)改變模擬流量之比較分析 28 4.2.2 振動腔與進出口層厚度(Zu)改變壓電片最大位移之比較分析 30 4.2.3 振動腔與進出口層厚度(Zu)改變在流固耦合交界面之最大受力比較分析 31 第五章 結論與未來展望 32 5.1 結論 32 5.2 未來展望 33 5.3 感謝 34 參考文獻 36 | |
| dc.language.iso | zh-TW | |
| dc.subject | 壓電無閥式微幫浦 | zh_TW |
| dc.subject | 流固耦合數值模擬 | zh_TW |
| dc.subject | 振動腔設計 | zh_TW |
| dc.subject | 振動腔與進出口層的厚度 | zh_TW |
| dc.subject | PZT valveless micropump | en |
| dc.subject | FSI numerical simulation | en |
| dc.subject | design chamber | en |
| dc.subject | thickness of layer of chamber and inlet and outlet | en |
| dc.title | 新式振動腔設計對無閥式微幫浦效能影響之數值模擬 | zh_TW |
| dc.title | Numerical Simulations on the Effect of the New design of the Chamber in Valveless Micropump | en |
| dc.type | Thesis | |
| dc.date.schoolyear | 102-1 | |
| dc.description.degree | 碩士 | |
| dc.contributor.oralexamcommittee | 吳光鐘(Kuang-Chong Wu),王安邦(An-Bang Wang),趙聖德(Sheng-Der Chao),黃冠榮(Kuan-Rong Huang) | |
| dc.subject.keyword | 壓電無閥式微幫浦,流固耦合數值模擬,振動腔設計,振動腔與進出口層的厚度, | zh_TW |
| dc.subject.keyword | PZT valveless micropump,FSI numerical simulation,design chamber,thickness of layer of chamber and inlet and outlet, | en |
| dc.relation.page | 94 | |
| dc.rights.note | 有償授權 | |
| dc.date.accepted | 2013-12-24 | |
| dc.contributor.author-college | 工學院 | zh_TW |
| dc.contributor.author-dept | 應用力學研究所 | zh_TW |
| Appears in Collections: | 應用力學研究所 | |
Files in This Item:
| File | Size | Format | |
|---|---|---|---|
| ntu-102-1.pdf Restricted Access | 7.11 MB | Adobe PDF |
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.