Please use this identifier to cite or link to this item:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/33569
Full metadata record
???org.dspace.app.webui.jsptag.ItemTag.dcfield??? | Value | Language |
---|---|---|
dc.contributor.advisor | 黃坤祥(Kuen-Shyang Hwang) | |
dc.contributor.author | Fu-Cheng Yen | en |
dc.contributor.author | 顏福成 | zh_TW |
dc.date.accessioned | 2021-06-13T04:47:53Z | - |
dc.date.available | 2006-07-24 | |
dc.date.copyright | 2006-07-24 | |
dc.date.issued | 2006 | |
dc.date.submitted | 2006-07-16 | |
dc.identifier.citation | [1] K. H. Lindner, “High Density P/M Gears by Enhanced Solid-State Sintering”, Advances in Powder Metallurgy and Particulate Materials, 1996, Vol. 3, pp. 11.221-11.235.
[2] E. A. Brandes and C. J. Smithells, Smithells Metals Reference Book, London:Butterworth-Heinemann, 1992, pp. 13.19-13.20. [3] R. Link, “Advances in PM Structural and Material Process Technology”, Euro PM97 Plenary Session, Germany, 1997, pp. 20-26. [4] G. Cizron and P. Lacombe, “A Dilatometeric Study of the Isothermal Sintering of Carbonyl Iron Powder”, Comptes Rendues, 1955, Vol. 241, pp. 409-410. [5] F. V. Lenel, Powder Metallurgy Principles and Application, MPIF, 1980, pp. 220-221. [6] S. L. Forss, “Some Aspects of the Sintering of Iron Powder”, Modern Developments in Powder Metallurgy, ed. by H. H. Hausner, 1966, Vol. 2, pp. 3-11 [7] 黃坤祥,粉末冶金學,中華民國粉末冶金學會,2003,155-156頁。 [8] O. Kubaschewski, Iron Binary Phase Diagrams, New York:Springer-Verlag , 1982, pp. 85-86. [9] F.V. Lenel, “Iron Article and Methode of Making Same”, United States Patent, 1940, No. 2,226,520. [10] P. Engdahl, “Iron Based Powder, Component Produced Therefrom an d Method of Producing The Component,” United States Patent, 1998, No. 5,728,238. [11] C. Lindberg and P. Engdahl, “Iron Based Powder Containing Mo, P and C”, United States Patent, 1999, No. 5,918,293. [12] B. Johansson, “Powder Composition and Method for the Preparation of Sintered Products”, Republic of China (Taiwan) Patent, 1999, No. 386,920. [13] P. Engdahl, “Mechanical Properties and Microstructure of Phosphorous Alloyed Sintered Steel”, Modern Development in Powder Metallurgy, 1988, Vol. 22, pp. 655-665. [14] C. Lindberg, “A New Fe-Mo-P Sintered Steel with Extremely High Impact Strength”, Advances in Powder Metallurgy and Particulate Materials, 1992, Vol. 3, pp. 99-106. [15] G. J. Shu and K. S Hwang, “High Density Powder Injection Molding Compacts Prepared from a Feedstock Containing Coarse Powders”, Materials Transactions, 2004, Vol. 45, No. 10, pp. 2999-3004. [16] G. Straffelini, V. Fontanari, A. Molinari, and B. Tesi, “Tensile and Fatigue behaviour of Phosphorus Alloyed Sintered Steels”, Powder Metallurgy, 1993, Vol. 36, No. 2, pp. 135-141. [17] A. Molinari, G. Straffelini, V. Fontanari, and R. Canteri, “Sintering and Microstructure of Phosphorus Steels”, Powder Metallurgy, 1992, Vol. 35, No. 4, pp. 285-291. [18] K. S. Hwang and K.H. Lin, “Effect of Sintering Parameters on the Magnetic Properties of Fe-0.45%P Sintered Materials”, Powder Metallurgy, 1992, Vol. 35, No.4, PP. 292-296. [19] W. F. Smith, Structure and Properties of Engineering Alloys, 2nd Edition, 1993, pp. 136. [20] H. Danninger and B. Üregen, “Embrittlement of PM Steels through Interaction of Molybdenum and Phosphorous”, Euro PM97 Mechanical Properties, pp. 319-326. [21] S. Gowri and J. A. Lund, “Densification by Solid State Sintering in Ferrous P/M”, Advances in Powder Metallurgy, 1989, Vol. 1, pp. 139-140. [22] I. Gabrielov, C. Wilson, T. Weilbaker, A. Barrows, F. Hanejko, and G. Ellis, “P/M High Strength Magnetic Alloys”, Advances in Powder Metallurgy and Particulate Materials, 2001, Vol. 12, pp. 2001. [23] R. W. K. Honeycombe and P. Hancock, Steels Microstructure and Properties, Metallurgy and Materials Science Series, 1981, pp. 55-75. [24] R. M. German, Powder Metallurgy of Iron and Steel, A Wiley-Interscience Publication, 1998, pp. 11. [25] A. K. Sinha, Physical Metallurgy Handbook, McGraw Hill, 1976, pp. 1.16. [26] H. Y. Lai, L. Chuanxi, and Y. Hongyu, “Distribution of Phosphorous in Fe-P-C-Cu-Mo Sintered Alloy and Its Effect on Properties”, Modern Developments in Powder Metallurgy, 1985, Vol. 16, pp. 107-122. [27] F. J. Semel, “Properties of Parts Made from a Binder Treared 0.45% Phosphorous Containing Iron Powder Blend”, Progress in Powder Metallurgy, 1987, Vol. 43, pp. 723-748. [28] R. C. O’Brien, “Impact and Fatigue Characterization of Selected Ferrous P/M Materials”, Progress in Powder Metallurgy, 1987, Vol. 43, pp. 749-775. [29] D. Krecar, J. Zwanziger, V. Vassileva, H. Danninger, and H. Hutter, “2D and 3D SIMS Investigations on Sintered Steels”, Applied Surface Science, 2005, Vol. 252, pp. 282-285. [30] G. S. Upadhyaya and M. Homiuddin, “Effect of Alloying Additions on Sintering of Iron-Phosphorous Premixes”, Sintering-Theory and Practice, 1981, pp. 291-298. [31] Md. Hamiuddin and G. S. Upadhyaya, “Effect of Copper on Sintered Prperties of Phosphorous-Containing Ternary Iron Powder Premixes”, Powder Metallurgy International, 1982, Vol. 14, No. 1, pp. 20-24. [32] T. Kohno, M. J. Koczak, V. Rajagopalan, and Y. Nishino, “Sintering Improvements in Strength and Dimensional Control Utilizing Eutectic Additions in Iron-Copper-Carbon Alloys”, Modern Developments in Powder Metallurgy, 1985, Vol. 15, pp. 521-540. [33] L. E. G. Cambronero, J. M. Torralba, and J. M. R. Prieto, “Mechanical Properties of Cu-P Sintered Alloyed Steels:Study of The Copper Influence on Dimensional Changes”, Science of Sintering, 1989, pp. 487-494. [34] I. Gabrielov, C. Wilson, T. Weilbaker, and A. Barrows, F. Hanejko and G. Ellis, “P/M High Strength Magnetic Alloys”, Advances in Powder Metallurgy and Particulate Materials, 2001, Vol. 12, pp. 2001. [35] R. R. D. Avillez and P. R. Rios, “The Influence of Carbon on The Phosphorous Segregation in Iron Alloys”, Scripta Metallurgica, 1983, Vol. 17, pp. 677-680. [36] S. Suzuki, M. Obata, K. Abiko, and H. Kimura, “Effect of Carbon on The Grain Boundary Segregation of Phosphorous in α–Iron”, Scripta Metallurgica, 1983, Vol. 17, pp. 1325-1328. [37] S. H. Hong et al., “The Reduction of The Interfacial Segregation of Phosphorous and Its Embrittlement Effect by Lanthanum Addition in A W-Ni-Fe Heavy Alloy”, Metallurgical Transactions A, 1991, Vol. 22A, pp. 2969-2974. [38] C. I. Garcia et al., “Reducing Temper Embrittlement by Lanthanide Additions”, Journal of Metals, 1985, pp. 22-28. [39] J. A. Lund, Y. Tanaka, and X. Qu, “Flux-Enhancement of Alloying in Iron-3% Silicon Compacts”, The International Journal of Powder Metallurgy, 1988, Vol. 24, No. 4, pp. 301-313. [40] J. Takekawa, “Enhancement of Sintering of Injection Molded Ferrous Mixed Powder Compacts by Silane Treatment”, Materials Transactions, JIM, 1996, Vol. 37, No. 2, pp. 157-162. [41] H. Danninger, “Sintering of Mo Alloyed P/M Steels Prepared from Elemental Powders”, Powder Metallurgy International, 1992, Vol. 24, No. 2, pp. 73-79. [42] J. S. Sheasby, “Powder Metallurgy of Iron-Aluminum”, The International Journal of Powder Metallurgy and Powder Technology, 1979, Vol. 15, No. 4, pp. 301-305. [43] S. Thamboo, G. W. ell, and J. P. Hirth, “The Mechanical Properties of RSR Processed Fe-Si-Al Alloys”, The International Journal of Powder Metallurgy and Powder Technology, 1983, Vol. 19, No. 3, pp. 211-222. | |
dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/33569 | - |
dc.description.abstract | 金屬射出成形(Metal Injection Molding, MIM)可以製造出形狀複雜、表面粗糙度佳且ㄧ次淨形之零件,但利用MIM製程所得之生胚密度僅為50-60%,因此必須藉由燒結來達到堪用的密度,故一般初始粉末通常都採用10μm以下的細粉,配合著1200-1300℃的高溫,持溫至少2小時,以達到94%以上之密度。而高溫燒結所伴隨著即是高設備成本與高能源消耗,此大大降低MIM產品的競爭力,故本研究主要是設計出一個能適用於低溫燒結的合金組成,使之能在一般設備成本較不昂貴且國內技術也較為成熟的低溫網帶爐下進行燒結,就可得到至少90%以上的燒結密度,及不錯的機械性質。
而本實驗也証實了利用Fe-0.7P-0.6C合金在1080℃持溫30分鐘後,即能得到密度7.4g/cm3、強度800MPa、硬度HRB98與伸長率12%的機械性質,此已超出美國粉末冶金協會(MPIF)中具有最佳機械性質之MIM-4605合金,且利用EPMA與SEM觀察破斷後的組織發現,即使在低溫短時間下燒結,亦可得到元素分佈非常均勻的組織與酒窩狀延性破裂結構。 另外,本實驗亦嘗試找出P可能產生偏析的含量與其發生的原因,而由實驗結果得知,當Fe-C系合金中P含量超過0.7wt%時,破斷面會從原本具有延性特性的酒窩狀組織變成具脆性的沿晶破裂組織。 而在添加過多種合金元素後,仍以Fe-0.7P-C系合金在低溫短時間燒結過後具有不錯的機械性質。 | zh_TW |
dc.description.abstract | Alloyed parts with complicated shape, smooth surface toughness and near net shape can be fabricated in metal injection molding (MIM) process. But green parts made by MIM process just have only 50-60% relative density, it is necessary to use lower than 10μm ultra fine powder as starting powder and sinter at 1200-1300℃ high temperature for 2 horses then 94% relative density can be ontained.
Higher equipment cost and energy consumption followed by high temperature sintering result in lower competition for MIM process. So design alloy composition for low temperature sintering to make allying parts sinter at belt furnace with lower cost then have sintered density above 90% and good mechanical properties. It is showed that Fe-0.7P-C sintered at 1080℃ for 30mins can get the value of 7.4g/cm3 in sintered density, 800MPa in ultimate tensile strength, HRB98 in hardness, 12% in elongation in this study, that is superior to standard MIM-4605 counterpart which has better mechanical properties in MPIF. The uniform elemental distribution and ductile dimple structure can be observed by EPMA and SEM equipment even sintered at low temperature Additionally, the possibility of P content causing segregation and its mechanism were also studied in this experiment. According to the experimental results, when P content in Fe-C alloy is more than 0.7wt%, the original ductile dimple structure turning into brittle intergranular structure on fracture surface was observed. Fe-0.7-C alloy sintered at low temperature for short time has optimal mechanical properties as compared to other counterparts in this study. | en |
dc.description.provenance | Made available in DSpace on 2021-06-13T04:47:53Z (GMT). No. of bitstreams: 1 ntu-95-R93527013-1.pdf: 21975110 bytes, checksum: 74269d46fdedc0f27a813a38438bd668 (MD5) Previous issue date: 2006 | en |
dc.description.tableofcontents | Abstract…………………………………………………………….. Ⅰ
摘要…………………………………………………………….…... Ⅲ 目錄…………………………………………………………….…... Ⅴ 第一章 簡介……………………………………………….……... 1 第二章 文獻回顧…………………………………………….…... 4 2-1 低溫燒結合金………………………………………….….. 4 2-2 合金粉的配置…………………………………………...… 8 2-3 射料的準備……………………………………………...… 8 2-3-1 粉末性質…………………………………………….... 8 2-3-2 黏結劑性質………………………………………….... 9 2-4 射出成形………………………………………………...… 10 2-5 脫脂………………………………………………….…..… 10 2-5-1 溶脫………………………………………………...…. 11 2-5-2 熱脫………………………………………………...…. 12 2-6 燒結……………………………………………………...… 12 2-6-1 合金元素對鐵燒結行為與機械性質之影響…………………………………………………………..…... 12 2-6-1-1 P對鐵燒結行為與機械性質之影響……………………………………………………….…… 15 2-6-1-2 Si對鐵燒結行為與機械性質之影響………………………………………………………….… 26 2-6-1-3 Mo對鐵燒結行為與機械性質之影響………………………………………………………..…... 31 2-6-1-4 Al對鐵燒結行為與機械性質之影響……………………………………………………….…… 32 2-6-1-5 Sn對鐵燒結行為與機械性質之影響……………………………………………………………. 37 2-6-1-6 Ti對鐵燒結行為與機械性質之影響………………………………………………………….… 39 第三章 實驗……………………………………………………... 42 3-1 實驗設計………………………………………………….. 42 3-2 原料…………………………………………………….…. 43 3-2-1 基礎粉…………………………………………….…... 43 3-2-2 其它粉末……………………………………….……... 45 3-3 混合方式與混煉……………………………………….…. 48 3-4 射出成形……………………………………………….…. 48 3-5 脫脂…………………………………………………….…. 50 3-5-1 溶劑脫脂………………………………………….….. 50 3-5-2 熱脫脂…………………………………………….….. 50 3-6 燒結…………………………………………………….…. 50 3-7 性質測試……………………………………………….…. 51 3-7-1 燒結行為之觀察……………………………………... 51 3-7-2 C含量的量測………………………………….….. 53 3-7-3 燒結密度的量測………………………………….….. 54 3-7-4 金相製備……………………………………………... 54 3-7-5 機械性質的測試…………………………………...… 55 3-7-6 脫脂過程中脫脂速率之量測與試片微結構之觀察................................................................................................ 55 3-8 實驗儀器…………………………………………….……. 56 第四章 實驗結果與討論………………………………………… 59 4-1 溶劑脫脂…………………………………………………... 59 4-2 熱脫脂……………………………………………………... 63 4-3 燒結………………………………………………………... 72 4-3-1 燒結溫度與持溫時間對Fe-0.7P-C系合金之影響………………………………………………………………. 72 4-3-1-1 燒結溫度與持溫時間對Fe-0.7P-C系合金C含量之影響..................................................................................... 72 4-3-1-2 燒結溫度與持溫時間對Fe-0.7P-C系合金燒結密度之影響……………………………………………………. 73 4-3-1-3 燒結溫度與持溫時間對Fe-0.7P-C系合金均質性與顯微組織…………………………………………………. 75 4-3-1-4 燒結溫度與持溫時間對Fe-0.7P-C系合金硬度與拉伸強度之影響……………………………………………. 80 4-3-1-5 燒結溫度與持溫時間對Fe-0.7P-C系合金延性之影響…………………………………………………………. 80 4-3-2 燒結氣氛對Fe-0.7P-C系合金之影響……………….. 85 4-3-2-1 燒結氣氛對Fe-0.7P-C系合金C含量之影響…………………………………………………………… 85 4-3-2-2 燒結氣氛對Fe-0.7P-C系合金燒結密度之影響……………………………………………………………. 87 4-3-2-3 燒結氣氛對Fe-0.7P-C系合金均質性與顯微組織之影響………………………………………………………. 87 4-3-2-4 燒結氣氛對Fe-0.7P-C系合金硬度與拉伸強度之影響…………………………………………………………. 90 4-3-2-5 燒結氣氛對Fe-0.7P-C系合金延性之影響……………………………………………………………. 91 4-3-3 P含量對Fe-C系合金之影響………………………... 95 4-3-3-1 P含量對Fe-C系合金燒結密度之影響……………………………………………………………. 95 4-3-3-2 P含量對Fe-C系合金C含量之影響………………………………………………………….… 96 4-3-3-3 P含量對Fe-C系合金均質性與顯微組織之影響..…………………………………………………………... 97 4-3-3-4 P含量對Fe-C系合金硬度與拉伸強度之影響….………………………………………………………… 102 4-3-3-5 P含量對Fe-C系合金延性之影響…………………………………………………….……… 102 4-3-4 合金元素對Fe-C系合金之影響………………………………………………………………. 107 4-3-4-1 合金元素對Fe-C系合金碳含量之影響………………………………………………………….… 107 4-3-4-2 合金元素對Fe-C系合金燒結密度之影響……………………………………………………………. 108 4-3-4-3 合金元素對Fe-C系合金均質性與顯微組織之影響………………………………………………………….… 114 4-3-4-4 合金元素對Fe-C系合金硬度與拉伸強度之影響……………………………………………………………. 119 4-3-4-5 合金元素對Fe-C系合金延性之影響……………………………………………………….…… 120 4-3-5 合金元素對Fe-0.7P-C系合金之影響………………………………………………………………. 123 4-3-5-1 合金元素對Fe-0.7P-C系合金碳含量之影響………………………………………………………….… 123 4-3-5-2 合金元素對Fe-0.7P-C系合金燒結密度之影響……………………………………………………………. 124 4-3-5-3 合金元素對Fe-0.7P-C系合金均質性與顯微組織之影響………………………………………………………. 125 4-3-5-4 合金元素對Fe-0.7P-C系合金硬度與拉伸強度之影響…………………………………………………………. 131 4-3-5-5 合金元素與氧化物對Fe-0.7P-C系合金延性之影響……………………………………………………………. 132 4-3-6 氧化物對Fe-0.7P-C系合金之影響…………………. 135 4-3-6-1 氧化物對Fe-0.7P-C系合金碳含量之影響……………………………………………………………. 135 4-3-6-2 氧化物對Fe-0.7P-C系合金燒結密度之影響……………………………………………………………. 136 4-3-6-3 氧化物對Fe-0.7P-C系合金均質性與顯微組織之影響…………………………………………………………. 137 4-3-6-4 氧化物對Fe-0.7P-C系合金硬度與拉伸強度之影響……………………………………………………………. 141 4-3-6-5 氧化物對Fe-0.7P-C系合金延性之影響…….................................................................................… 141 第五章 結論……………………………………………………... 145 5-1 低溫燒結合金….………………………………………….. 145 第六章 未來工作……………………………………………....... 147 第七章 參考文獻……………………………………………....... 148 附錄………………………………………………………………… 152 | |
dc.language.iso | zh-TW | |
dc.title | 鐵-磷-碳系低溫燒結合金之製程及機械性質 | zh_TW |
dc.title | Processing and Mechanical Properties of Low-Temperature Sintered Fe-P-C Alloy | en |
dc.type | Thesis | |
dc.date.schoolyear | 94-2 | |
dc.description.degree | 碩士 | |
dc.contributor.oralexamcommittee | 林招松(Chao-Sung Lin),潘永村(Yeong-Tsuen Pan) | |
dc.subject.keyword | 金屬粉末射出成形,低溫燒結,網帶爐,α相燒結,Fe-0.7P-C系合金, | zh_TW |
dc.subject.keyword | Metal Injection Molding,Low Temperature Sintering,Belt Furnace,α-Phase Sintering,Fe-0.7P-C Alloy, | en |
dc.relation.page | 153 | |
dc.rights.note | 有償授權 | |
dc.date.accepted | 2006-07-17 | |
dc.contributor.author-college | 工學院 | zh_TW |
dc.contributor.author-dept | 材料科學與工程學研究所 | zh_TW |
Appears in Collections: | 材料科學與工程學系 |
Files in This Item:
File | Size | Format | |
---|---|---|---|
ntu-95-1.pdf Restricted Access | 21.46 MB | Adobe PDF |
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.