請用此 Handle URI 來引用此文件:
http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/18433
完整後設資料紀錄
DC 欄位 | 值 | 語言 |
---|---|---|
dc.contributor.advisor | 李貫銘 | |
dc.contributor.author | Chia-Hao Chang | en |
dc.contributor.author | 張嘉澔 | zh_TW |
dc.date.accessioned | 2021-06-08T01:04:58Z | - |
dc.date.copyright | 2014-08-21 | |
dc.date.issued | 2014 | |
dc.date.submitted | 2014-08-20 | |
dc.identifier.citation | [1] 張文彬, '基於聲音和圖像的刀具磨損狀態監測技術的研究,' 浙江工業大學碩士論文, 2003.
[2] H. Takeyama and R. Murata, 'Basic investigation of tool wear,' American Society of Mechanical Engineers -- Transactions -- Journal of Engineering for Industry, pp. 33-38, 1963. [3] N. Abukhshim, P. Mativenga, and M. Sheikh, 'Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining,' International Journal of Machine Tools and Manufacture, vol. 46, pp. 782-800, 2006. [4] D. A. Stephenson, 'Assessment of steady-state metal cutting temperature models based on simultaneous infrared and thermocouple data,' Journal of Engineering for Industry, vol. 113, pp. 121-128, 1991. [5] A. Basti, T. Obikawa, and J. Shinozuka, 'Tools with built-in thin film thermocouple sensors for monitoring cutting temperature,' International Journal of Machine Tools and Manufacture, vol. 47, pp. 793-798, 2007. [6] W. Grzesik, 'Determination of temperature distribution in the cutting zone using hybrid analytical-FEM technique,' International Journal of Machine Tools and Manufacture, vol. 46, pp. 651-658, 2006. [7] Y. Dogu, E. Aslan, and N. Camuscu, 'A numerical model to determine temperature distribution in orthogonal metal cutting,' Journal of Materials Processing Technology, vol. 171, pp. 1-9, 2006. [8] D. W. Yen and P. K. Wright, 'A remote temperature sensing technique for estimating the cutting interface temperature distribution,' Journal of Engineering for Industry, vol. 108, pp. 252-263, 1986. [9] A. B. T. C. K. J. Trigger, 'Analytical evaluation of metal cutting temperatures,' ASME vol. 73, pp. 109-120, 1951. [10] D. L. R. a. W. N. Giedt, 'Heat transfer and temperature distribution in a metal cutting tool,' ASME vol. 78, p. 1507, 1956. [11] A. Tay, M. Stevenson, and G. D. V. Davis, 'Using the finite element method to determine temperature distributions in orthogonal machining,' Proceedings of the institution of mechanical engineers, vol. 188, pp. 627-638, 1974. [12] P. K. W. a. J. G. C. M.G. Stevenson, 'Further developments in applying the finite element method to the calculation of temperature distributions in machining and comparisons with experiment,' ASME, vol. 105, p. 149 1983. [13] A. Feteira, 'Negative temperature coefficient resistance (NTCR) ceramic thermistors: an industrial perspective,' Journal of the American Ceramic Society, vol. 92, pp. 967-983, 2009. [14] J.-J. Salgon, F. Robbe-Valloire, J. Blouet, and J. Bransier, 'A mechanical and geometrical approach to thermal contact resistance,' International journal of heat and mass transfer, vol. 40, pp. 1121-1129, 1997. [15] S. Iqbal, P. Mativenga, and M. Sheikh, 'A comparative study of the tool–chip contact length in turning of two engineering alloys for a wide range of cutting speeds,' The International Journal of Advanced Manufacturing Technology, vol. 42, pp. 30-40, 2009. [16] 黃竣志, '氧化鎳熱敏電阻於溫度感測微陣列之應用,' 國立臺灣大學碩士論文, 2013. [17] V. Ostafiev, K. Weinert, S. Ostafiev, and A. Kharkevich, 'Tool heat transfer in orthogonal metal cutting,' Journal of Manufacturing Science and Engineering, vol. 121, pp. 541-549, 1999. [18] Y. J. Yang and C. C. Yu, 'Extraction of heat-transfer macromodels for MEMS devices,' Journal of micromechanics and microengineering, vol.14, pp. 587–596,2004. [19] W.E. Arnoldi, 'The principle of minimized iterations in the solution of the matrix eigenvalues problem,' Quarterly of Applied Mathematics, vol.9, pp. 17–29,1951. [20] L.S. Lasdon, 'The conjugate gradient method for optimal comtrol problem,' IEEE Transactions on Automatic Control, Ac-12, pp. 132–138,1987. [21] 林宜弘, 吳志庭, '應用簡單最佳化法輔助平面熱源法同時量測熱傳導係數,' 農業機械學刊, 4(2), 1997. | |
dc.identifier.uri | http://tdr.lib.ntu.edu.tw/jspui/handle/123456789/18433 | - |
dc.description.abstract | 在切削作業中,刀尖溫度之量測方法仍有諸多困難,因為最高溫度發生位置位於刀具與切屑之接觸面,若使用紅外線熱像儀容易受到切屑或切削液的干擾。若使用熱電偶,亦難以直接到達該溫度面作量測,且必須於刀具做鑽孔加工,增加成本。
為了提高監控系統在經濟上之效益,本研究開發出適用於車削加工之溫度感測器,此感測器採用微熱敏電阻,擁有相當高之熱敏指標B值,使得溫度量測範圍以及分辨率皆得以提升,另一方面實現感測元件微小化以及小範圍內量測多點溫度值的可能。不但能夠大幅降低感測器對溫度之反應時間,更可以實現陣列溫度場之量測。為達成在線監控(Online Monitoring)之目標,本研究使用有限元素法配合精簡模型理論(Model Order Reduction)以提高運算速度,並利用微熱敏電阻量測之溫度與精簡模型求解逆向熱傳問題(Inverse Heat Conduction Problem, IHCP),並以共軛梯度法推估刀尖平均溫度。 研究結果證實,本論文提出之溫度感測器可對溫度變化做出快速的反應。在非切削實驗中,精簡模型能準確預測刀尖平均溫度變化,由此確認本論文提出之切削溫度即時監測技術具有相當之準確性,非切削實驗中,平均差異為5%。最後並以車削加工為例,說明本研究提出之量測方法之可行性。 | zh_TW |
dc.description.abstract | In metal cutting operation, there are still many difficulties in measuring cutting temperature, because the location of the maximum temperature occurs at the contact surface between the tool and the chip. Using an infrared thermal imager is susceptible to interference by chips or cutting fluid. If a thermocouple or thermistor is used, it is difficult to directly measure the tool tip temperature. Drilling a hole in the tool must be done, and it will increase costs. At the same time, cutting temperature is a good indicator for tool wear or tool condition monitoring.
In order to apply cutting temperature to monitoring in machining process monitoring, this study developed a novel temperature sensor for turning. It is a micro-thermistor made of NiO with a very high value of the thermal index B, so the resolution is very high compared to other types of temperature sensors. Moreover, miniaturized sensors can make multi-point temperature measurement within a small range possible. The tool tip temperature is estimated by the finite element method(FEM) with the measure temperature, which is known as inversed heat conduction problem(IHCP). In this study, the model order reduction(MOR) is used to increase computing speed of the FEM. In solving the IHCP, the conjugate gradient method is adopted to estimate the average temperature of the tip. The results confirmed that the temperature sensor developed in this study can respond quickly to changes of cutting temperatures. In the non-cutting experiments, the average tool tip temperature can be accurately and quickly predicted with the micro-thermistor array and the conjugate gradient method with MOR. Finally, the proposed methodology is applied to estimate the tool tip temperature in turning. | en |
dc.description.provenance | Made available in DSpace on 2021-06-08T01:04:58Z (GMT). No. of bitstreams: 1 ntu-103-R01522722-1.pdf: 2588213 bytes, checksum: 71d27f4ac7c2ea7ca16b7e67d51b9864 (MD5) Previous issue date: 2014 | en |
dc.description.tableofcontents | 致謝 I
摘要 II ABSTRACT III 目錄 IV 圖目錄 VI 表目錄 IX 第一章 緒論 1 1.1 研究動機與目的 1 1.2 論文架構 3 第二章 文獻回顧 4 2.1 切削溫度在線監控 4 2.2 切削溫度之數學模式 5 2.3 熱敏電阻 7 2.4 NTC THERMISTOR 參數說明 8 2.5 計算接觸面積 10 第三章 微感測器 11 3.1 熱敏電阻 11 3.2 溫度感測元件之製造程序 12 3.3 液膜燒結溫度 13 3.4 溫度感測元件測試 14 第四章 切削溫度推估 17 4.1 切削溫度之數學模式 17 4.2 建立刀片模型網格與邊界條件 17 4.3 精簡模型理論 24 4.4 逆向熱傳導問題 25 第五章 實驗設計與規劃 27 5.1 實驗規劃 27 5.2 實驗器具 29 5.3 實驗設備 31 5.4 裝設微感測器於車刀 38 5.5 非切削實驗設計 39 5.5.1 實驗步驟 40 5.6 切削實驗設計 41 5.6.1 實驗步驟 41 第六章 實驗結果分析與討論 44 6.1 精簡模型不同階數比較 44 6.2 非切削實驗驗證結果 45 6.3 切削實驗驗證結果 48 第七章 結論與未來展望 51 7.1 結論 51 7.2 未來展望 52 參考文獻 53 | |
dc.language.iso | zh-TW | |
dc.title | 運用微感測器於切削溫度之即時監測 | zh_TW |
dc.title | On-line Monitoring of Cutting Temperature with Microsensors | en |
dc.type | Thesis | |
dc.date.schoolyear | 102-2 | |
dc.description.degree | 碩士 | |
dc.contributor.oralexamcommittee | 楊宏智,黃振康,王榮昌 | |
dc.subject.keyword | 切削溫度,微感測器,精簡模型, | zh_TW |
dc.subject.keyword | cutting temperature,micro-sensors,model order reduction, | en |
dc.relation.page | 54 | |
dc.rights.note | 未授權 | |
dc.date.accepted | 2014-08-20 | |
dc.contributor.author-college | 工學院 | zh_TW |
dc.contributor.author-dept | 機械工程學研究所 | zh_TW |
顯示於系所單位: | 機械工程學系 |
文件中的檔案:
檔案 | 大小 | 格式 | |
---|---|---|---|
ntu-103-1.pdf 目前未授權公開取用 | 2.53 MB | Adobe PDF |
系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。